MSI Starcam 370i

[zole052]

Evo da napokon rijesim i problem sa web kamerom, pa bi vas molio za pomoc...
jedino pametno sto sam naso je driver koji navodno radi sa nekim kamerama a s nekim ne (meni narano ne radi)
http://www.pamplast.com/gspca/
Kameru testiram u skype-u i ne radi iako je prepoznaje, imam za odabrati ko "USB camera (/dev/video0)" ali kada mu dam da testira umjesto slike samo mi izbaci zelen ekran sa malo nekih fiksnih smetnji na vrhu prikaza kamere

[Suko]

A što ti kaže lsusb za tu kameru?

[zole052]

Bus 002 Device 004: ID 0c45:60c0 Microdia PC Camera with Mic (SN9C105)

[Suko]

Po onom što vidim na netu driver koji si našao bi trebao biti baš za tvoj tip kamere.
60c0
Ima neki 60fc za koji taj driver ne radi.
A jel si probao ovo:

Ovako:
1) sudo pico /etc/modprobe.d/blacklist
upises na kraju:
blacklist sn9cxxx
blacklist sn9c102
blacklist gpsca
2) resetujes sistem
3) skines drajver i raspakujes ga
4) udjes u msicam folder
5) ./c
6)sudo pico /etc/modprobe.d/options
upisete na kraju:
options msicam camera_type=2

to bi trebalo da radi pod uslovom da imate Msi Starcam 370i sa usb id-om (0c45 60c0/60fc)
drajver radi i sa camorama i sa cheese i sa skype

To sam našao na http://www.ubuntu-rs.org/forum/viewthread.php?tid=6050
Izgleda obećavajuće.

[zole052]

na zalost nece
neznam da li to ima veze sa tome sto sam vec jednom instaliro te drivere... ne bi trebalo... ako se dobro sjecam onda nije izbacilo ova dva errora na kraju

Kod: Označi sve

zzankola@zzankola ~/msicam $ ./c
[sudo] password for zzankola: 

 REMOVE the old module if present
ERROR: Module msicam does not exist in /proc/modules

 CLEAN gspca source tree
rm -r -f *.o decoder/.gspcadecoder.o.cmd decoder/*.o \
	.gspca.o.cmd .gspca* *.o *.ko *.mod.* core *.i \
	*.symvers *.err

 COMPILE gspca Please Wait ....!!

 INSTALL gspca in the kernel binary tree
mkdir -p /lib/modules/`uname -r`/kernel/drivers/usb/media/
rm -f /lib/modules/`uname -r`/kernel/drivers/media/video/msicam.ko
install -c -m 0644 msicam.ko /lib/modules/`uname -r`/kernel/drivers/usb/media/
install: cannot stat `msicam.ko': No such file or directory
make: *** [install] Error 1

 LOAD gspca in memory 
FATAL: Module msicam not found.

 PRINT COMPILATION MESSAGES if ERRORS look kgspca.err 
make -C /lib/modules/`uname -r`/build SUBDIRS=/home/zzankola/msicam CC=cc modules
make[1]: Entering directory `/usr/src/linux-headers-2.6.27-7-generic'
  CC [M]  /home/zzankola/msicam/gspca_core.o
/home/zzankola/msicam/gspca_core.c:54:27: error: asm/semaphore.h: No such file or directory
In file included from /home/zzankola/msicam/gspca_core.c:256:
/home/zzankola/msicam/Sonix/proc.h: In function ‘sn9cxxx_proc_init’:
/home/zzankola/msicam/Sonix/proc.h:52: error: ‘proc_root’ undeclared (first use in this function)
/home/zzankola/msicam/Sonix/proc.h:52: error: (Each undeclared identifier is reported only once
/home/zzankola/msicam/Sonix/proc.h:52: error: for each function it appears in.)
/home/zzankola/msicam/Sonix/proc.h: In function ‘sn9cxxx_proc_unload’:
/home/zzankola/msicam/Sonix/proc.h:76: error: ‘proc_root’ undeclared (first use in this function)
/home/zzankola/msicam/Sonix/proc.h: In function ‘sn9cxxx_proc_write’:
/home/zzankola/msicam/Sonix/proc.h:116: warning: cast to pointer from integer of different size
/home/zzankola/msicam/Sonix/proc.h:116: warning: comparison between pointer and integer
In file included from /home/zzankola/msicam/Sonix/sonix.h:79,
                 from /home/zzankola/msicam/gspca_core.c:257:
/home/zzankola/msicam/Sonix/sn9cxxx.h: In function ‘sn9cxxx_stopN’:
/home/zzankola/msicam/Sonix/sn9cxxx.h:531: warning: unused variable ‘regF1’
/home/zzankola/msicam/Sonix/sn9cxxx.h:529: warning: unused variable ‘stophv7131’
/home/zzankola/msicam/Sonix/sn9cxxx.h: In function ‘sn9cxxx_start’:
/home/zzankola/msicam/Sonix/sn9cxxx.h:570: warning: unused variable ‘err’
/home/zzankola/msicam/Sonix/sn9cxxx.h:563: warning: unused variable ‘regD4’
/home/zzankola/msicam/Sonix/sn9cxxx.h: In function ‘sn9cxxx_getexposure’:
/home/zzankola/msicam/Sonix/sn9cxxx.h:683: warning: unused variable ‘lexpo’
/home/zzankola/msicam/Sonix/sn9cxxx.h:683: warning: unused variable ‘mexpo’
/home/zzankola/msicam/Sonix/sn9cxxx.h:683: warning: unused variable ‘hexpo’
/home/zzankola/msicam/Sonix/sn9cxxx.h: In function ‘sn9cxxx_setexposure’:
/home/zzankola/msicam/Sonix/sn9cxxx.h:706: warning: unused variable ‘expotimes’
/home/zzankola/msicam/Sonix/sn9cxxx.h:705: warning: unused variable ‘data’
/home/zzankola/msicam/Sonix/sn9cxxx.h:704: warning: unused variable ‘gainMo’
/home/zzankola/msicam/Sonix/sn9cxxx.h:703: warning: unused variable ‘expoMo10’
/home/zzankola/msicam/Sonix/sn9cxxx.h:702: warning: unused variable ‘expoMof’
/home/zzankola/msicam/Sonix/sn9cxxx.h:700: warning: unused variable ‘sensorgo’
/home/zzankola/msicam/Sonix/sn9cxxx.h:699: warning: unused variable ‘doit’
/home/zzankola/msicam/Sonix/sn9cxxx.h:698: warning: unused variable ‘Expodoit’
/home/zzankola/msicam/Sonix/sn9cxxx.h: In function ‘sn9cxxx_setbrightness’:
/home/zzankola/msicam/Sonix/sn9cxxx.h:726: warning: unused variable ‘expotimesret’
/home/zzankola/msicam/Sonix/sn9cxxx.h:726: warning: unused variable ‘expo’
/home/zzankola/msicam/Sonix/sn9cxxx.h: In function ‘sn9cxxx_setcolors’:
/home/zzankola/msicam/Sonix/sn9cxxx.h:839: warning: unused variable ‘blue’
/home/zzankola/msicam/Sonix/sn9cxxx.h: In function ‘sn9cxxx_setAutobright’:
/home/zzankola/msicam/Sonix/sn9cxxx.h:856: warning: unused variable ‘expotimesret’
/home/zzankola/msicam/Sonix/sn9cxxx.h: In function ‘sn9cxxx_setgain’:
/home/zzankola/msicam/Sonix/sn9cxxx.h:930: warning: unused variable ‘g3’
/home/zzankola/msicam/Sonix/sn9cxxx.h:929: warning: unused variable ‘g2’
/home/zzankola/msicam/Sonix/sn9cxxx.h:928: warning: unused variable ‘g1’
/home/zzankola/msicam/Sonix/sn9cxxx.h:927: warning: unused variable ‘sensorgo’
/home/zzankola/msicam/Sonix/sn9cxxx.h:926: warning: unused variable ‘doit’
/home/zzankola/msicam/gspca_core.c: In function ‘spca5xx_ioctl’:
/home/zzankola/msicam/gspca_core.c:1820: error: implicit declaration of function ‘video_usercopy’
/home/zzankola/msicam/gspca_core.c: At top level:
/home/zzankola/msicam/gspca_core.c:1966: error: unknown field ‘owner’ specified in initializer
/home/zzankola/msicam/gspca_core.c:1966: warning: initialization from incompatible pointer type
/home/zzankola/msicam/gspca_core.c:1968: error: unknown field ‘type’ specified in initializer
/home/zzankola/msicam/gspca_core.c: In function ‘spca50x_create_sysfs’:
/home/zzankola/msicam/gspca_core.c:2126: error: implicit declaration of function ‘video_device_create_file’
/home/zzankola/msicam/gspca_core.c:2137: error: implicit declaration of function ‘video_device_remove_file’
/home/zzankola/msicam/gspca_core.c: In function ‘spcaDetectCamera’:
/home/zzankola/msicam/gspca_core.c:2178: warning: unused variable ‘fw’
/home/zzankola/msicam/gspca_core.c: In function ‘spca5xx_probe’:
/home/zzankola/msicam/gspca_core.c:2263: error: incompatible types in assignment
make[2]: *** [/home/zzankola/msicam/gspca_core.o] Error 1
make[1]: *** [_module_/home/zzankola/msicam] Error 2
make[1]: Leaving directory `/usr/src/linux-headers-2.6.27-7-generic'
make: *** [default] Error 2
Done Building

[Grof]

Evo da napokon rijesim i problem sa web kamerom, pa bi vas molio za pomoc...
jedino pametno sto sam naso je driver koji navodno radi sa nekim kamerama a s nekim ne (meni narano ne radi)
http://www.pamplast.com/gspca/
Kameru testiram u skype-u i ne radi iako je prepoznaje, imam za odabrati ko "USB camera (/dev/video0)" ali kada mu dam da testira umjesto slike samo mi izbaci zelen ekran sa malo nekih fiksnih smetnji na vrhu prikaza kamere

Koja distra?

Jesi probao kameru sa Ekigom, Cheesom i sl programima? Skype je problematičan sam po sebi...

[zole052]

Mint 6, evo probo sam sa cheesom i opet istu stvar dobijem a sto se tice skypea zbog njega mi i treba kamera...

[Grof]

znači istu stvar dobijaš i na Ekigi i na Cheesu i na Skypeu? Isti zeleni ekran?

[zole052]

je, tocno, u svim programima dobijem istu sliku!

[Grof]

je, tocno, u svim programima dobijem istu sliku!

Meni se čini da ti keernel modul ne barata sa kamerom kako treba...
Trebat će to malo bolje istražiti i progooglati.