glaskoncILLa je napisao/la:kako izgleda taj modules.conf?
Kod: Označi sve
### This file is automatically generated by update-modules
#
# Please do not edit this file directly. If you want to change or add
# anything please take a look at the files in ./etc/modules.d and read
# the manpage for update-modules(8).
#
### update-modules: start processing /etc/modules.d/av5100
# modules.d configuration file for AV5100
# For more information please read:
# README
# Configurable module parameters
# ------------------------------
# radio: controls state of radio (1=on, 0=off)
### update-modules: end processing /etc/modules.d/av5100
### update-modules: start processing /etc/modules.d/fuse
# modules.d config file for FUSE
# this file was automatically generated from linux-mod.eclass
# Configurable module parameters
# ------------------------------
# user_allow_other: Allow non root user to specify the "allow_other" or "allow_root" mount options
# mount_max: Maximum number of FUSE mounts allowed, if -1 then unlimited (default: 1000)
### update-modules: end processing /etc/modules.d/fuse
### update-modules: start processing /etc/modules.d/ipw2100
# modules.d configuration file for IPW2100
# For more information please read:
# README.ipw2100
# Configurable module parameters
# ------------------------------
# debug: debug level
# mode: network mode (0=BSS,1=IBSS,2=Monitor)
# channel: channel
# associate: auto associate when scanning (default on)
# disable: manually disable the radio (default 0 [radio on])
### update-modules: end processing /etc/modules.d/ipw2100
### update-modules: start processing /etc/modules.d/ipw2200
# modules.d configuration file for IPW2200
# For more information please read:
# README.ipw2200
# Configurable module parameters
# ------------------------------
# disable: manually disable the radio (default 0 [radio on])
# associate: auto associate when scanning (default on)
# auto_create: auto create adhoc network (default on)
# led: enable led control on some systems (default 0 off)
# debug: debug output mask
# channel: channel to limit associate to (default 0 [ANY])
# qos_enable: enable all QoS functionalitis
# qos_burst_enable: enable QoS burst mode
# qos_no_ack_mask: mask Tx_Queue to no ack
# burst_duration_CCK: set CCK burst value
# burst_duration_OFDM: set OFDM burst value
# mode: network mode (0=BSS,1=IBSS,2=Monitor)
# hwcrypto: enable hardware crypto (default on)
### update-modules: end processing /etc/modules.d/ipw2200
### update-modules: start processing /etc/modules.d/ipw3945d
install ipw3945 /sbin/modprobe --ignore-install ipw3945; sleep 0.5; /etc/init.d/ipw3945d start
remove ipw3945 /etc/init.d/ipw3945d stop; /sbin/modprobe -r --ignore-remove ipw3945
### update-modules: end processing /etc/modules.d/ipw3945d
### update-modules: start processing /etc/modules.d/ivtv-fb
# modules.d configuration file for IVTV-FB
# For more information please read:
# FB_DOCS
# Configurable module parameters
# ------------------------------
# ivtv_fb_card_id: ID number of ivtv card to use as framebuffer device (0-7)
### update-modules: end processing /etc/modules.d/ivtv-fb
### update-modules: start processing /etc/modules.d/pbe5
# modules.d configuration file for PBE5
# Configurable module parameters
# ------------------------------
# radio: controls state of radio (1=on, 0=off)
### update-modules: end processing /etc/modules.d/pbe5
### update-modules: start processing /etc/modules.d/rt2400
# modules.d configuration file for RT2400
# Internal Aliases - Do not edit
# ------------------------------
alias ra? rt2400
# Configurable module parameters
# ------------------------------
# debug: Enable level: accepted values: 1 to switch debug on, 0 to switch debug off.
# ifname: Network device name (default ra%d)
### update-modules: end processing /etc/modules.d/rt2400
