LAN problem nakon friske instalacije
Moderator/ica: Moderatori/ce
- Heisenberg
- Postovi: 2232
- Pridružen/a: 29 lis 2012, 07:57
- OS: SLCKWR 14.1
LAN problem nakon friske instalacije
Pozdrav.
Napokon sam probao novu distribuciju.
Prvo je bio openSUSE 12.2 KDE (objasnit cu kasnije zasto nisam na njemu)
Pa sam instalirao Fedoru 17.
Naime, instalacija je prosla regularno. Bez ikakvih komplikacija.
Onda, kad sam stavio lan, nemam interneta. Normalno pokazuje da je spojen, ali kad udjem u mozillu, pokazuje error.
Namjestio sam firewall i sve, da prihvaca eth0 i wlan0.
Kad sam prije instalirao Ubuntu, normalno je radio lan.
Onda sam jucer navecer probao openSUSE i opet ovaj isti problem kao i na fedori trenutno.
Mislio sam da je neki interni problem u suseu ali ocigledno nije.
Da li ima rijesenje za ovaj problem ili da se vratim na sjebuntu?
edit: vratio sam se na ubuntu 12.10
stavio lan i opet nezeli na net.
mislim da je stvar u driverima, vjerojatno su izbrisani.
i sad, nemogu na laptop.krasno.
Napokon sam probao novu distribuciju.
Prvo je bio openSUSE 12.2 KDE (objasnit cu kasnije zasto nisam na njemu)
Pa sam instalirao Fedoru 17.
Naime, instalacija je prosla regularno. Bez ikakvih komplikacija.
Onda, kad sam stavio lan, nemam interneta. Normalno pokazuje da je spojen, ali kad udjem u mozillu, pokazuje error.
Namjestio sam firewall i sve, da prihvaca eth0 i wlan0.
Kad sam prije instalirao Ubuntu, normalno je radio lan.
Onda sam jucer navecer probao openSUSE i opet ovaj isti problem kao i na fedori trenutno.
Mislio sam da je neki interni problem u suseu ali ocigledno nije.
Da li ima rijesenje za ovaj problem ili da se vratim na sjebuntu?
edit: vratio sam se na ubuntu 12.10
stavio lan i opet nezeli na net.
mislim da je stvar u driverima, vjerojatno su izbrisani.
i sad, nemogu na laptop.krasno.
“Small shifts in your thinking, and small changes in your energy, can lead to massive alterations of your end result.”
- glaskoncILLa
- Postovi: 5678
- Pridružen/a: 28 vel 2009, 16:36
Re: LAN problem nakon friske instalacije
koji error ti izbaci?
daj
ifconfig
route -n
cat /etc/resolv.conf
cat /etc/network/interfaces
lspci
pa pasteaj output ovdje
daj
ifconfig
route -n
cat /etc/resolv.conf
cat /etc/network/interfaces
lspci
pa pasteaj output ovdje
...."Have you mooed today?"...
..It’s that time of the decade: I’m reinstalling Debian..
..It’s that time of the decade: I’m reinstalling Debian..
Re: LAN problem nakon friske instalacije
Odi na Korzo, tamo imaš wlan

Like some other animals, the gecko can perform a neat trick when threatened by a predator: it can amputate its own tail. The dropped tail serves to distract the predator, and by losing it, the lizard can run faster.
-
Slamd64
AW: LAN problem nakon friske instalacije
Vidi je li dhcpcd startan ako koristis dhcp.
Gesendet von meinem MT11i mit Tapatalk 2
Gesendet von meinem MT11i mit Tapatalk 2
- Heisenberg
- Postovi: 2232
- Pridružen/a: 29 lis 2012, 07:57
- OS: SLCKWR 14.1
Re: LAN problem nakon friske instalacije
necemo se vrijeđat lolstefan je napisao/la:Odi na Korzo, tamo imaš wlan![]()
“Small shifts in your thinking, and small changes in your energy, can lead to massive alterations of your end result.”
- Heisenberg
- Postovi: 2232
- Pridružen/a: 29 lis 2012, 07:57
- OS: SLCKWR 14.1
Re: LAN problem nakon friske instalacije
sad neznam dal sam trebao svaku zasebnu al evo.glaskoncILLa je napisao/la:koji error ti izbaci?
daj
ifconfig
route -n
cat /etc/resolv.conf
cat /etc/network/interfaces
lspci
pa pasteaj output ovdje
Kod: Označi sve
matej@matej-Aspire-7551:~$ ifconfig route-n cat/etc/resolv.conf cat /etc/network lspci
Usage:
ifconfig [-a] [-v] [-s] <interface> [[<AF>] <address>]
[add <address>[/<prefixlen>]]
[del <address>[/<prefixlen>]]
[[-]broadcast [<address>]] [[-]pointopoint [<address>]]
[netmask <address>] [dstaddr <address>] [tunnel <address>]
[outfill <NN>] [keepalive <NN>]
[hw <HW> <address>] [metric <NN>] [mtu <NN>]
[[-]trailers] [[-]arp] [[-]allmulti]
[multicast] [[-]promisc]
[mem_start <NN>] [io_addr <NN>] [irq <NN>] [media <type>]
[txqueuelen <NN>]
[[-]dynamic]
[up|down] ...
<HW>=Hardware Type.
List of possible hardware types:
loop (Local Loopback) slip (Serial Line IP) cslip (VJ Serial Line IP)
slip6 (6-bit Serial Line IP) cslip6 (VJ 6-bit Serial Line IP) adaptive (Adaptive Serial Line IP)
strip (Metricom Starmode IP) ash (Ash) ether (Ethernet)
ax25 (AMPR AX.25) netrom (AMPR NET/ROM) rose (AMPR ROSE)
tunnel (IPIP Tunnel) ppp (Point-to-Point Protocol) hdlc ((Cisco)-HDLC)
lapb (LAPB) arcnet (ARCnet) dlci (Frame Relay DLCI)
frad (Frame Relay Access Device) sit (IPv6-in-IPv4) fddi (Fiber Distributed Data Interface)
hippi (HIPPI) irda (IrLAP) ec (Econet)
x25 (generic X.25) eui64 (Generic EUI-64)
<AF>=Address family. Default: inet
List of possible address families:
unix (UNIX Domain) inet (DARPA Internet) inet6 (IPv6)
ax25 (AMPR AX.25) netrom (AMPR NET/ROM) rose (AMPR ROSE)
ipx (Novell IPX) ddp (Appletalk DDP) ec (Econet)
ash (Ash) x25 (CCITT X.25)
“Small shifts in your thinking, and small changes in your energy, can lead to massive alterations of your end result.”
- glaskoncILLa
- Postovi: 5678
- Pridružen/a: 28 vel 2009, 16:36
Re: AW: LAN problem nakon friske instalacije
dhcpd je serverski daemon, odnosno to imaju dhcp serveri, ne klijenti.Slamd64 je napisao/la:Vidi je li dhcpcd startan ako koristis dhcp.
Gesendet von meinem MT11i mit Tapatalk 2
trebao si svaku zasebno, zato sam i odvojio u posebne redove.matej je napisao/la:sad neznam dal sam trebao svaku zasebnu al evo.glaskoncILLa je napisao/la:koji error ti izbaci?
daj
ifconfig
route -n
cat /etc/resolv.conf
cat /etc/network/interfaces
lspci
pa pasteaj output ovdje
Kod: Označi sve
matej@matej-Aspire-7551:~$ ifconfig route-n cat/etc/resolv.conf cat /etc/network lspci Usage: ifconfig [-a] [-v] [-s] <interface> [[<AF>] <address>] [add <address>[/<prefixlen>]] [del <address>[/<prefixlen>]] [[-]broadcast [<address>]] [[-]pointopoint [<address>]] [netmask <address>] [dstaddr <address>] [tunnel <address>] [outfill <NN>] [keepalive <NN>] [hw <HW> <address>] [metric <NN>] [mtu <NN>] [[-]trailers] [[-]arp] [[-]allmulti] [multicast] [[-]promisc] [mem_start <NN>] [io_addr <NN>] [irq <NN>] [media <type>] [txqueuelen <NN>] [[-]dynamic] [up|down] ... <HW>=Hardware Type. List of possible hardware types: loop (Local Loopback) slip (Serial Line IP) cslip (VJ Serial Line IP) slip6 (6-bit Serial Line IP) cslip6 (VJ 6-bit Serial Line IP) adaptive (Adaptive Serial Line IP) strip (Metricom Starmode IP) ash (Ash) ether (Ethernet) ax25 (AMPR AX.25) netrom (AMPR NET/ROM) rose (AMPR ROSE) tunnel (IPIP Tunnel) ppp (Point-to-Point Protocol) hdlc ((Cisco)-HDLC) lapb (LAPB) arcnet (ARCnet) dlci (Frame Relay DLCI) frad (Frame Relay Access Device) sit (IPv6-in-IPv4) fddi (Fiber Distributed Data Interface) hippi (HIPPI) irda (IrLAP) ec (Econet) x25 (generic X.25) eui64 (Generic EUI-64) <AF>=Address family. Default: inet List of possible address families: unix (UNIX Domain) inet (DARPA Internet) inet6 (IPv6) ax25 (AMPR AX.25) netrom (AMPR NET/ROM) rose (AMPR ROSE) ipx (Novell IPX) ddp (Appletalk DDP) ec (Econet) ash (Ash) x25 (CCITT X.25)
...."Have you mooed today?"...
..It’s that time of the decade: I’m reinstalling Debian..
..It’s that time of the decade: I’m reinstalling Debian..
- Heisenberg
- Postovi: 2232
- Pridružen/a: 29 lis 2012, 07:57
- OS: SLCKWR 14.1
Re: LAN problem nakon friske instalacije
ifconfig
route-n
cat /etc/resolv.conf
cat /etc/network/interfaces
lspci
Kod: Označi sve
matej@matej-Aspire-7551:~$ ifconfig
eth0 Link encap:Ethernet HWaddr 20:6a:8a:3e:9a:00
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
Interrupt:16
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:356 errors:0 dropped:0 overruns:0 frame:0
TX packets:356 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:28860 (28.8 KB) TX bytes:28860 (28.8 KB)
wlan0 Link encap:Ethernet HWaddr 88:9f:fa:33:f3:af
inet addr:192.168.5.99 Bcast:192.168.5.255 Mask:255.255.255.0
inet6 addr: fe80::8a9f:faff:fe33:f3af/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:11326 errors:0 dropped:0 overruns:0 frame:0
TX packets:538 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:852439 (852.4 KB) TX bytes:66823 (66.8 KB)
Kod: Označi sve
matej@matej-Aspire 7551:~$ route-n
command not foundKod: Označi sve
matej@matej-Aspire-7551:~$ cat /etc/resolv.conf
# Dynamic resolv.conf(5) file for glibc resolver(3) generated by resolvconf(8)
# DO NOT EDIT THIS FILE BY HAND -- YOUR CHANGES WILL BE OVERWRITTEN
nameserver 127.0.1.1
search gigaset.lan
Kod: Označi sve
matej@matej-Aspire-7551:~$ cat /etc/network/interfaces
# interfaces(5) file used by ifup(8) and ifdown(8)
auto lo
iface lo inet loopback
Kod: Označi sve
matej@matej-Aspire-7551:~$ lspci
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS880 Host Bridge
00:02.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (ext gfx port 0)
00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 0)
00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780/RS880 PCI to PCI bridge (PCIE port 1)
00:11.0 SATA controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 SATA Controller [AHCI mode]
00:12.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:12.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:13.0 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB OHCI0 Controller
00:13.2 USB controller: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 USB EHCI Controller
00:14.0 SMBus: Advanced Micro Devices [AMD] nee ATI SBx00 SMBus Controller (rev 42)
00:14.2 Audio device: Advanced Micro Devices [AMD] nee ATI SBx00 Azalia (Intel HDA) (rev 40)
00:14.3 ISA bridge: Advanced Micro Devices [AMD] nee ATI SB7x0/SB8x0/SB9x0 LPC host controller (rev 40)
00:14.4 PCI bridge: Advanced Micro Devices [AMD] nee ATI SBx00 PCI to PCI Bridge (rev 40)
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
02:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI Whistler [AMD Radeon HD 6600M Series]
02:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI Turks/Whistler HDMI Audio [Radeon HD 6000 Series]
03:00.0 Ethernet controller: Broadcom Corporation NetLink BCM57780 Gigabit Ethernet PCIe (rev 01)
06:00.0 Network controller: Broadcom Corporation BCM43225 802.11b/g/n (rev 01)
“Small shifts in your thinking, and small changes in your energy, can lead to massive alterations of your end result.”
- glaskoncILLa
- Postovi: 5678
- Pridružen/a: 28 vel 2009, 16:36
Re: LAN problem nakon friske instalacije
dodaj u /etc/network/interfaces ispod svega (dakle nemoj brisati ono sto vec pise unutra)
auto eth0
iface eth0 inet dhcp
pa restartaj komp
auto eth0
iface eth0 inet dhcp
pa restartaj komp
...."Have you mooed today?"...
..It’s that time of the decade: I’m reinstalling Debian..
..It’s that time of the decade: I’m reinstalling Debian..
- Heisenberg
- Postovi: 2232
- Pridružen/a: 29 lis 2012, 07:57
- OS: SLCKWR 14.1
Re: LAN problem nakon friske instalacije
glaskoncILLa je napisao/la:dodaj u /etc/network/interfaces ispod svega (dakle nemoj brisati ono sto vec pise unutra)
auto eth0
iface eth0 inet dhcp
pa restartaj komp
could not save the file /etc/network/interfaces.
you do not have the permissions necessary to save the file. please check that you typed the location correctly and try again.
“Small shifts in your thinking, and small changes in your energy, can lead to massive alterations of your end result.”