Linux za Sve forum

Bok svima ja sam ssik i imam problem. Ubuntu, odnosno linux mint 10 lxde, mi se boota oko 4 min. i to me izluduje.. na starijim verzijama nisam imao taj problem.. znam u cemu je stvar ali neznam kako problem otkloniti zato cu postaviti podatke sa .log file-a (dio .log file-a gdje nastaje problem) u nadi da mi neko moze pomoci, neznam koliko ti podatci mogu biti od pomoci ali valjda ce se netko zainteresirati za moj problem

Hvala!!

[ 2.372799] scsi 1:0:0:0: CD-ROM HL-DT-ST CD-RW GCE-8480B 1.03 PQ: 0 ANSI: 5
[ 2.716627] sdb1
[ 2.718687] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 32.832143] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 32.832154] sr 1:0:0:0: CDB: Mode Sense(10): 5a 00 2a 00 00 00 00 00 80 00
[ 32.832173] ata2.00: cmd a0/01:00:00:80:00/00:00:00:00:00/a0 tag 0 dma 16512 in
[ 32.832175] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
[ 32.832179] ata2.00: status: { DRDY }
[ 37.872082] ata2: link is slow to respond, please be patient (ready=0)
[ 42.856080] ata2: device not ready (errno=-16), forcing hardreset
[ 42.856094] ata2: soft resetting link
[ 43.044338] ata2.00: configured for UDMA/33
[ 43.060335] ata2.01: configured for MWDMA2
[ 43.084329] ata2.00: configured for UDMA/33
[ 43.100332] ata2.01: configured for MWDMA2
[ 43.100360] ata2: EH complete
[ 73.824109] ata2.00: limiting speed to UDMA/25:PIO4
[ 73.824120] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 73.824127] sr 1:0:0:0: CDB: Mode Sense(10): 5a 00 2a 00 00 00 00 00 80 00
[ 73.824145] ata2.00: cmd a0/01:00:00:80:00/00:00:00:00:00/a0 tag 0 dma 16512 in
[ 73.824147] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
[ 73.824151] ata2.00: status: { DRDY }
[ 78.864102] ata2: link is slow to respond, please be patient (ready=0)
[ 83.848071] ata2: device not ready (errno=-16), forcing hardreset
[ 83.848085] ata2: soft resetting link
[ 84.044316] ata2.00: configured for UDMA/25
[ 84.060343] ata2.01: configured for MWDMA2
[ 84.076334] ata2.00: configured for UDMA/25
[ 84.092332] ata2.01: configured for MWDMA2
[ 84.092357] ata2: EH complete
[ 114.912131] ata2.00: limiting speed to PIO4
[ 114.912142] ata2.00: exception Emask 0x0 SAct 0x0 SErr 0x0 action 0x6 frozen
[ 114.912149] sr 1:0:0:0: CDB: Mode Sense(10): 5a 00 2a 00 00 00 00 00 80 00
[ 114.912168] ata2.00: cmd a0/01:00:00:80:00/00:00:00:00:00/a0 tag 0 dma 16512 in
[ 114.912170] res 40/00:03:00:00:00/00:00:00:00:00/a0 Emask 0x4 (timeout)
[ 114.912174] ata2.00: status: { DRDY }
[ 119.952089] ata2: link is slow to respond, please be patient (ready=0)
[ 124.936098] ata2: device not ready (errno=-16), forcing hardreset
[ 124.936112] ata2: soft resetting link
[ 125.124350] ata2.00: configured for PIO4
[ 125.140336] ata2.01: configured for MWDMA2
[ 125.156333] ata2.00: configured for PIO4
[ 125.172354] ata2.01: configured for MWDMA2
[ 125.172383] ata2: EH complete
[ 125.173716] sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
[ 125.173723] Uniform CD-ROM driver Revision: 3.20
[ 125.174011] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 125.174204] sr 1:0:0:0: Attached scsi generic sg2 type 5
[ 125.175866] scsi 1:0:1:0: Direct-Access ATA QUANTUM Pioneer A05. PQ: 0 ANSI: 5
[ 125.177332] sd 1:0:1:0: Attached scsi generic sg3 type 0
[ 125.177860] sd 1:0:1:0: [sdc] 2113776 512-byte logical blocks: (1.08 GB/1.00 GiB)
[ 125.178114] sd 1:0:1:0: [sdc] Write Protect is off

dmesg.log.gz: (10.7 KiB) Preuzeto 47 puta.

Pozdrav,

Cini mi se da ti je CDROM/DVD uredjaj postao nefunkcionalan ili se pokvario (pretpostavljam da je upravo taj redjaj onaj koji se nalazi na drugom ata kanalu). Provjeri uredjaj, provjeri kablove, provjeri jumper (na sto je postavljen, master, slave ili CS).

Bootaj s neke live verzije linuxa i provjeri dogadja li se isto. Ukoliko ne pokusaj nadograditi kernel i/ili libata paket na svojoj instalaciji linuxa.

Nakon bootanja masine, logovima mozes pristupiti na nacin:

# dmesg > dmesg.log
# gzip dmesg.log

To ce stvoriti dmesg.gz datoteku koju mozes prikljuciti svojem odgovoru kako bi ljudi vidjeli sto se dogadja a sukladno tome ti preporucili koje korake mozes izvesti kako bi doveo pod kontrolu ovaj problem.

Da upravo je CDROM uređaj taj koji stvara probleme, međutim on radi nakon boota, s njime sam i instalirao linux. Probao sam i sa nadogradnjom kernela na noviju verziju, ali bezuspješno, do verzije ubuntua 10.04 sve je radilo super (sto se tiče hardware-a) kablovi su u redu, pokušao sam perkopčavati ali opet dobijem error na CDROM-u sad nisam siguran za jumper, ali mislim da je na slave

Trenutno nemam bas vremena pa cu samo postati dkmsg. gz a kad se vratim kući pokušati ču ono što si mi savjetovao.

Postaj output komande:

# hdparm -i /dev/sdc

Pokusaj bootati linux dodavanjem dolje navedenog kernel argumenta (prijavi promjene):

noapic

Linux za Sve forum

[Ubuntu] 4min. boot-a [help]

[Ubuntu] 4min. boot-a [help]

Re: [Ubuntu] 4min. boot-a [help]

Re: [Ubuntu] 4min. boot-a [help]

Re: [Ubuntu] 4min. boot-a [help]