Izgubio wireless vezu - molim pomoć

[sm]

wg311v3 : driver installed
device (11AB:1FAA) present

Ovo gore znaci da vec postoji driver te da je hardware prisutan. Sada moras iskonfigurirati parametre svoje wireless mreze, sto znaci pokusaj to iskonfigurirati kroz "konfiguriraj mrezu", iako vjerujem da isto mozes kroz ono graficko sucelje za ndiswrapper.

Za sada pokusaj standardnom metodom, a ona je koristeci "konfiguriraj mrezu".

I ja sam vidio da piše da je driver instaliran i da je hardware prisutan, samo što se, kao i na početku, kod konfiguracije mreže traže brojke (BSSID i MAC address koje ne znam, niti znam kako ih doznati.

Moja mreža ZyXEL je tamo navedena a za konfiguraciju trebaju ti podaci.

Zadnji put kad smo radili nisam ih trebao posebno upisivati.

Ne postoji način da se mreža automatski prepozna pa da se samo priključim na nju upisivanjem njenog pristupnog koda (password)?

[drade]

Pogledati cu kako si to rijesio prvi put pa ti javim.

[sm]

Pogledati cu kako si to rijesio prvi put pa ti javim.

Ok, do tada ne radim ništa.

[drade]

Suko je napisao, pa eto ja cu iskoristiti njegove upute:

Dakle, prvo izdaj komandu:

sudo ifconfig -a
sudo iwlist wlan0 scan

Postaj output ovdje.

[sm]

Suko je napisao, pa eto ja cu iskoristiti njegove upute:

Dakle, prvo izdaj komandu:

sudo ifconfig -a
sudo iwlist wlan0 scan

Postaj output ovdje.

Evo:

stevo@Mojkomp:~$ sudo ifconfig -a
[sudo] password for stevo:
eth0 Link encap:Ethernet HWaddr 00:0d:87:af:db:76
inet addr:192.168.1.32 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20d:87ff:feaf:db76/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:21836 errors:0 dropped:0 overruns:0 frame:0
TX packets:22285 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:20003931 (20.0 MB) TX bytes:3990613 (3.9 MB)
Interrupt:23

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:61 errors:0 dropped:0 overruns:0 frame:0
TX packets:61 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2265 (2.2 KB) TX bytes:2265 (2.2 KB)

stevo@Mojkomp:~$ sudo iwlist wlan0 scan
wlan0 Interface doesn't support scanning.

stevo@Mojkomp:~$

[drade]

Nadalje:

sudo modprobe ndiswrapper
sudo lshw -C network
sudo ifconfig -a
sudo iwconfig

[sm]

Nadalje:

sudo modprobe ndiswrapper
sudo lshw -C network
sudo ifconfig -a
sudo iwconfig

Već nakon prve komande je wireless mreža uspostavljena, i još radi!

Nastavio sam niz do kraja i evo outputa:

stevo@Mojkomp:~$ sudo modprobe ndiswrapper
WARNING: All config files need .conf: /etc/modprobe.d/ndiswrapper, it will be ignored in a future release.
stevo@Mojkomp:~$ sudo lshw -C network
*-network:0
description: Wireless interface
product: 88w8335 [Libertas] 802.11b/g Wireless
vendor: Marvell Technology Group Ltd.
physical id: 9
bus info: pci@0000:00:09.0
logical name: wlan0
version: 03
serial: 00:1b:2f:c6:cf:5e
width: 32 bits
clock: 66MHz
capabilities: pm bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=ndiswrapper+wg311v3 driverversion=1.56+NETGEAR,02/22/2005,3.1.1.7 ip=192.168.1.30 latency=32 link=yes multicast=yes wireless=IEEE 802.11g
resources: irq:17 memory:ea410000-ea41ffff memory:ea400000-ea40ffff
*-network:1
description: Ethernet interface
product: VT6102 [Rhine-II]
vendor: VIA Technologies, Inc.
physical id: 12
bus info: pci@0000:00:12.0
logical name: eth0
version: 78
serial: 00:0d:87:af:db:76
size: 100MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical tp mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=via-rhine driverversion=1.4.3 duplex=full ip=192.168.1.32 latency=32 link=yes maxlatency=8 mingnt=3 multicast=yes port=MII speed=100MB/s
resources: irq:23 ioport:e400(size=256) memory:ea422000-ea4220ff
stevo@Mojkomp:~$ sudo ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:0d:87:af:db:76
inet addr:192.168.1.32 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::20d:87ff:feaf:db76/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:22662 errors:0 dropped:0 overruns:0 frame:0
TX packets:23166 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:20563948 (20.5 MB) TX bytes:4127636 (4.1 MB)
Interrupt:23

lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:70 errors:0 dropped:0 overruns:0 frame:0
TX packets:70 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:2526 (2.5 KB) TX bytes:2526 (2.5 KB)

wlan0 Link encap:Ethernet HWaddr 00:1b:2f:c6:cf:5e
inet addr:192.168.1.30 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21bfec6:cf5e/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:1 errors:0 dropped:0 overruns:0 frame:0
TX packets:18 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:342 (342.0 B) TX bytes:3547 (3.5 KB)
Interrupt:17 Memory:ea400000-ea410000

stevo@Mojkomp:~$ sudo iwconfig
lo no wireless extensions.

eth0 no wireless extensions.

wlan0 IEEE 802.11g ESSID:"ZyXEL"
Mode:Managed Frequency:2.412 GHz Access Point: 00:13:49:BF:39:84
Bit Rate=54 Mb/s Sensitivity=-200 dBm
RTS thr=2346 B Fragment thr=2346 B
Encryption key:3236-3132-3935-3833-3130-3931-31 Security mode:open
Power Management:off
Link Quality:48/100 Signal level:-65 dBm Noise level:-96 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0

stevo@Mojkomp:~$

Trebam restartirati da vidimo da li se automatski uspostavlja?

[drade]

Ne, sacekaj, moramo jos par komandi natuci:

Prije nego nastavimo izdaj komandu te postaj output ovdje:

sudo cat /etc/rc.local

[sm]

Ne, sacekaj, moramo jos par komandi natuci:

Prije nego nastavimo izdaj komandu te postaj output ovdje:

sudo cat /etc/rc.local

Evo:

tevo@Mojkomp:~$ sudo cat /etc/rc.local
#!/bin/sh -e
#
# rc.local
#
# This script is executed at the end of each multiuser runlevel.
# Make sure that the script will "exit 0" on success or any other
# value on error.
#
# In order to enable or disable this script just change the execution
# bits.
#
# By default this script does nothing.

exit 0
sudo modprobe ndiswrapper

stevo@Mojkomp:~$

(ovo radim s wirelessa)

[drade]

Onda je to valjda to !

Malo si se namucio izdajuci silne komande i prckajuci po terminalu, iskompilirao si svoj prvi program, nadogradio kernel ... itd. Valjda uvidjas veliku moc koju linux ima, te njegovu fleksibilnost.

Happy computing.

D.