[RIJEŠENO] knetwork manager se pokvario

[Markec]

Hmm, a imaš li ti u kanti osim wirelessa i običnu mrežnu karticu? I ulaz za ethernet kabl?

imam
Laptop ti je HP COMPAQ NX9420

[Grof]

Aha! To što se vidi u prozoru od networkmanagera je samo ova eternetica (onaj eth0).

Tebi linux više uopće ne vidi wireless adapter. To je dublji problem od knetworkmanagera, čini mi se.

A prije je radilo, tebi je to jučer na večer prestalo radit, zar ne? Da li si nešto radio na Linuxu što je moglo uzrokovati prestanak rada kartice?

Ovaj notebook, koliko ja znam ima jedan gimb iznad tastarure koji pali i gasi wireless, i kad radi tamo gori plava ikonica.
Ajd, ako ga imaš probaj kliknut na taj gumb, pa ugasi/upali/ wireless fizički s tim gumbom...

[Markec]

Aha! To što se vidi u prozoru od networkmanagera je samo ova eternetica (onaj eth0).

Tebi linux više uopće ne vidi wireless adapter. To je dublji problem od knetworkmanagera, čini mi se.

A prije je radilo, tebi je to jučer na večer prestalo radit, zar ne? Da li si nešto radio na Linuxu što je moglo uzrokovati prestanak rada kartice?

Ovaj notebook, koliko ja znam ima jedan gimb iznad tastarure koji pali i gasi wireless, i kad radi tamo gori plava ikonica.
Ajd, ako ga imaš probaj kliknut na taj gumb, pa ugasi/upali/ wireless fizički s tim gumbom...

To sa tim gumbom sam pokusao vise puta, ne pomaze, obicno kada klikam po njoj se na dnu KDE trake ispise da je wireless isklucen ili ako upalim pokze da je uklucen. e a sad se to ne desava.

To je pocelo bas nakon resertiranja kada smo sredili drivere za grafu.

[Grof]

da, imam neki blagi osjećaj da instalacija grafe nije blacklistala driver za wireless.

ajd napravi ovo u terminalu:

Kod: Označi sve

lspci | grep net
lspci | grep wireless
lsmod | grep net

pa mi ispiši rezultate

[Markec]

Evo ti tekst spremjen s KATE,
nemogu ga otvoriti u windowsu, sorry,
a ti imas linux pa ti nije problem otvoriti.

[Grof]

ne znam što si mi to poslao... to je nekakav binarni file iz windowsa, to nije tekst.

Ajd, navečer ćemo dalje....poz.

[Markec]

ne znam što si mi to poslao... to je nekakav binarni file iz windowsa, to nije tekst.

Ajd, navečer ćemo dalje....poz.

moze, budem to ponovno napravio i stavio ovdje.
cujemo se veceras

[Markec]

evo

Kod: Označi sve

marko@Marko-PC:~$ lspci l grep net
Usage: lspci [<switches>]

-v              Be verbose
-n              Show numeric ID's
-nn             Show both textual and numeric ID's (names & numbers)
-b              Bus-centric view (PCI addresses and IRQ's instead of those seen by the CPU)
-x              Show hex-dump of the standard portion of config space
-xxx            Show hex-dump of the whole config space (dangerous; root only)
-xxxx           Show hex-dump of the 4096-byte extended config space (root only)
-s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]   Show only devices in selected slots
-d [<vendor>]:[<device>]        Show only selected devices
-t              Show bus tree
-m              Produce machine-readable output
-i <file>       Use specified ID database instead of /usr/share/misc/pci.ids.gz
-D              Always show domain numbers
-M              Enable `bus mapping' mode (dangerous; root only)
-P <dir>        Use specified directory instead of /proc/bus/pci
-H <mode>       Use direct hardware access (<mode> = 1 or 2)
-F <file>       Read configuration data from given file
-G              Enable PCI access debugging
marko@Marko-PC:~$ lspci l grep wireless
Usage: lspci [<switches>]

-v              Be verbose
-n              Show numeric ID's
-nn             Show both textual and numeric ID's (names & numbers)
-b              Bus-centric view (PCI addresses and IRQ's instead of those seen by the CPU)
-x              Show hex-dump of the standard portion of config space
-xxx            Show hex-dump of the whole config space (dangerous; root only)
-xxxx           Show hex-dump of the 4096-byte extended config space (root only)
-s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]   Show only devices in selected slots
-d [<vendor>]:[<device>]        Show only selected devices
-t              Show bus tree
-m              Produce machine-readable output
-i <file>       Use specified ID database instead of /usr/share/misc/pci.ids.gz
-D              Always show domain numbers
-M              Enable `bus mapping' mode (dangerous; root only)
-P <dir>        Use specified directory instead of /proc/bus/pci
-H <mode>       Use direct hardware access (<mode> = 1 or 2)
-F <file>       Read configuration data from given file
-G              Enable PCI access debugging
marko@Marko-PC:~$ lspci l grep net
Usage: lspci [<switches>]

-v              Be verbose
-n              Show numeric ID's
-nn             Show both textual and numeric ID's (names & numbers)
-b              Bus-centric view (PCI addresses and IRQ's instead of those seen by the CPU)
-x              Show hex-dump of the standard portion of config space
-xxx            Show hex-dump of the whole config space (dangerous; root only)
-xxxx           Show hex-dump of the 4096-byte extended config space (root only)
-s [[[[<domain>]:]<bus>]:][<slot>][.[<func>]]   Show only devices in selected slots
-d [<vendor>]:[<device>]        Show only selected devices
-t              Show bus tree
-m              Produce machine-readable output
-i <file>       Use specified ID database instead of /usr/share/misc/pci.ids.gz
-D              Always show domain numbers
-M              Enable `bus mapping' mode (dangerous; root only)
-P <dir>        Use specified directory instead of /proc/bus/pci
-H <mode>       Use direct hardware access (<mode> = 1 or 2)
-F <file>       Read configuration data from given file
-G              Enable PCI access debugging
marko@Marko-PC:~$

[Grof]

ne znak "1" nego znak "|" desniAlt+W ispred grep-a uvijek ide desniAlt+W za piping...

[marsovac]

ajd kad si već tu....meni knetwork manager uopće ne reagira kad kliknem njegovu ikonu.......koji mu je.....