Bizarno je to što se na router najnormalnije bežično spojim s dva mobitela i sa istim laptopom iz Windowsa7 no ne i iz Linuxa (eOS Luna 64 bit).
Što sam probao:
- spojiti se na net iz više Live distribucija (sve se spoje na router, ali dalje nema veze na net)
- promijeniti postavke u routeru; otvorio vezu (maknuo pass), promijenio naziv routera, mijenjao standarde spajanja (b,g,n u svim mogućim kombinacijama), dao fiksnu IP adresu, i možda još nešto ali se sad ne mogu sjetiti jer sam se zezao time noćas do dva
.. na kraju sam sve vratio na tvorničke postavke i samo stavio pass)Ako vam može pomoći ispod imate ispise za:
iwconfig
- Kod: Označi sve
dario@ProBook:~$ sudo iwconfig
eth0 no wireless extensions.
lo no wireless extensions.
wlan0 IEEE 802.11bgn ESSID:"LZS"
Mode:Managed Frequency:2.412 GHz Access Point: C8:D3:A3:35:13:F2
Bit Rate=58.5 Mb/s Tx-Power=16 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
Link Quality=62/70 Signal level=-48 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:4 Invalid misc:2 Missed beacon:0
dmesg:
- Kod: Označi sve
dario@ProBook:~$ sudo dmesg
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.8.0-35-generic (buildd@allspice) (gcc version 4.6.3 (Ubuntu/Linaro 4.6.3-1ubuntu5) ) #50~precise1-Ubuntu SMP Wed Dec 4 17:25:51 UTC 2013 (Ubuntu 3.8.0-35.50~precise1-generic 3.8.13.13)
[ 0.000000] Command line: BOOT_IMAGE=/boot/vmlinuz-3.8.0-35-generic root=UUID=702572f9-d7e7-4545-aee0-b9248631c929 ro quiet splash vt.handoff=7
[ 0.000000] KERNEL supported cpus:
[ 0.000000] Intel GenuineIntel
[ 0.000000] AMD AuthenticAMD
[ 0.000000] Centaur CentaurHauls
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000000-0x000000000009ebff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009ec00-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000bc6bffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bc6c0000-0x00000000bcebffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000bcec0000-0x00000000bcfbffff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000bcfc0000-0x00000000bcffefff] ACPI data
[ 0.000000] BIOS-e820: [mem 0x00000000bcfff000-0x00000000bcffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000bd000000-0x00000000bf9fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000e0000000-0x00000000efffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed10000-0x00000000fed13fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed18000-0x00000000fed19fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ffd80000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000023f7fffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] SMBIOS 2.6 present.
[ 0.000000] DMI: Hewlett-Packard HP ProBook 4530s/167C, BIOS 68SRR Ver. F.05 04/08/2011
[ 0.000000] e820: update [mem 0x00000000-0x0000ffff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] No AGP bridge found
[ 0.000000] e820: last_pfn = 0x23f800 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0FFC00000 mask FFFC00000 write-protect
[ 0.000000] 1 base 000000000 mask F80000000 write-back
[ 0.000000] 2 base 080000000 mask FC0000000 write-back
[ 0.000000] 3 base 0BE000000 mask FFE000000 uncachable
[ 0.000000] 4 base 0BD800000 mask FFF800000 uncachable
[ 0.000000] 5 base 100000000 mask F00000000 write-back
[ 0.000000] 6 base 200000000 mask FC0000000 write-back
[ 0.000000] 7 base 23F800000 mask FFF800000 uncachable
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
[ 0.000000] e820: last_pfn = 0xbd000 max_arch_pfn = 0x400000000
[ 0.000000] initial memory mapped: [mem 0x00000000-0x1fffffff]
[ 0.000000] Base memory trampoline at [ffff880000098000] 98000 size 24576
[ 0.000000] reserving inaccessible SNB gfx pages
[ 0.000000] init_memory_mapping: [mem 0x00000000-0xbcffffff]
[ 0.000000] [mem 0x00000000-0xbcffffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0xbcffffff @ [mem 0x1fffc000-0x1fffffff]
[ 0.000000] init_memory_mapping: [mem 0x100000000-0x23f7fffff]
[ 0.000000] [mem 0x100000000-0x23f7fffff] page 2M
[ 0.000000] kernel direct mapping tables up to 0x23f7fffff @ [mem 0xbc6ba000-0xbc6bffff]
[ 0.000000] RAMDISK: [mem 0x3546e000-0x36a2efff]
[ 0.000000] ACPI: RSDP 00000000000f2f60 00024 (v02 HPQOEM)
[ 0.000000] ACPI: XSDT 00000000bcffe120 0006C (v01 HPQOEM SLIC-MPC 0000000F 01000013)
[ 0.000000] ACPI: FACP 00000000bcffc000 000F4 (v03 HPQOEM 167C 0000000F HP 00000001)
[ 0.000000] ACPI: DSDT 00000000bcfd3000 237BB (v02 HPQOEM 167C 00000001 INTL 20060912)
[ 0.000000] ACPI: FACS 00000000bcfb9000 00040
[ 0.000000] ACPI: HPET 00000000bcffb000 00038 (v01 HPQOEM 167C 00000001 HP 00000001)
[ 0.000000] ACPI: APIC 00000000bcffa000 000BC (v01 HPQOEM 167C 00000001 HP 00000001)
[ 0.000000] ACPI: MCFG 00000000bcff9000 0003C (v01 HPQOEM 167C 00000001 HP 00000001)
[ 0.000000] ACPI: ASF! 00000000bcff8000 000A5 (v32 HPQOEM 167C 00000001 HP 00000001)
[ 0.000000] ACPI: SSDT 00000000bcfd0000 00266 (v01 HPQOEM SataAhci 00001000 INTL 20060912)
[ 0.000000] ACPI: SSDT 00000000bcfcf000 0048A (v01 HPQOEM PtidDevc 00001000 INTL 20060912)
[ 0.000000] ACPI: SSDT 00000000bcfce000 00918 (v01 PmRef Cpu0Ist 00003000 INTL 20060912)
[ 0.000000] ACPI: SSDT 00000000bcfcd000 009B1 (v01 PmRef CpuPm 00003000 INTL 20060912)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at [mem 0x0000000000000000-0x000000023f7fffff]
[ 0.000000] Initmem setup node 0 [mem 0x00000000-0x23f7fffff]
[ 0.000000] NODE_DATA [mem 0x23f7fb000-0x23f7fffff]
[ 0.000000] [ffffea0000000000-ffffea0008ffffff] PMD -> [ffff880236e00000-ffff88023edfffff] on node 0
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x00010000-0x00ffffff]
[ 0.000000] DMA32 [mem 0x01000000-0xffffffff]
[ 0.000000] Normal [mem 0x100000000-0x23f7fffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00010000-0x0009dfff]
[ 0.000000] node 0: [mem 0x00100000-0xbc6bffff]
[ 0.000000] node 0: [mem 0xbcfff000-0xbcffffff]
[ 0.000000] node 0: [mem 0x100000000-0x23f7fffff]
[ 0.000000] On node 0 totalpages: 2080335
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 142 pages reserved
[ 0.000000] DMA zone: 3776 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 11996 pages used for memmap
[ 0.000000] DMA32 zone: 755685 pages, LIFO batch:31
[ 0.000000] Normal zone: 20448 pages used for memmap
[ 0.000000] Normal zone: 1288224 pages, LIFO batch:31
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x02] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x03] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x04] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x05] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x06] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x07] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x00] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 0, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 4 hotplug CPUs
[ 0.000000] nr_irqs_gsi: 40
[ 0.000000] PM: Registered nosave memory: 000000000009e000 - 000000000009f000
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] PM: Registered nosave memory: 00000000bc6c0000 - 00000000bcec0000
[ 0.000000] PM: Registered nosave memory: 00000000bcec0000 - 00000000bcfc0000
[ 0.000000] PM: Registered nosave memory: 00000000bcfc0000 - 00000000bcfff000
[ 0.000000] PM: Registered nosave memory: 00000000bd000000 - 00000000bfa00000
[ 0.000000] PM: Registered nosave memory: 00000000bfa00000 - 00000000e0000000
[ 0.000000] PM: Registered nosave memory: 00000000e0000000 - 00000000f0000000
[ 0.000000] PM: Registered nosave memory: 00000000f0000000 - 00000000fec00000
[ 0.000000] PM: Registered nosave memory: 00000000fec00000 - 00000000fec01000
[ 0.000000] PM: Registered nosave memory: 00000000fec01000 - 00000000fed10000
[ 0.000000] PM: Registered nosave memory: 00000000fed10000 - 00000000fed14000
[ 0.000000] PM: Registered nosave memory: 00000000fed14000 - 00000000fed18000
[ 0.000000] PM: Registered nosave memory: 00000000fed18000 - 00000000fed1a000
[ 0.000000] PM: Registered nosave memory: 00000000fed1a000 - 00000000fed1c000
[ 0.000000] PM: Registered nosave memory: 00000000fed1c000 - 00000000fed20000
[ 0.000000] PM: Registered nosave memory: 00000000fed20000 - 00000000fee00000
[ 0.000000] PM: Registered nosave memory: 00000000fee00000 - 00000000fee01000
[ 0.000000] PM: Registered nosave memory: 00000000fee01000 - 00000000ffd80000
[ 0.000000] PM: Registered nosave memory: 00000000ffd80000 - 0000000100000000
[ 0.000000] e820: [mem 0xbfa00000-0xdfffffff] available for PCI devices
[ 0.000000] Booting paravirtualized kernel on bare hardware
[ 0.000000] setup_percpu: NR_CPUS:256 nr_cpumask_bits:256 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] PERCPU: Embedded 28 pages/cpu @ffff88023f400000 s84928 r8192 d21568 u262144
[ 0.000000] pcpu-alloc: s84928 r8192 d21568 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 2047685
[ 0.000000] Policy zone: Normal
[ 0.000000] Kernel command line: BOOT_IMAGE=/boot/vmlinuz-3.8.0-35-generic root=UUID=702572f9-d7e7-4545-aee0-b9248631c929 ro quiet splash vt.handoff=7
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] __ex_table already sorted, skipping sort
[ 0.000000] xsave: enabled xstate_bv 0x7, cntxt size 0x340
[ 0.000000] Checking aperture...
[ 0.000000] No AGP bridge found
[ 0.000000] Calgary: detecting Calgary via BIOS EBDA area
[ 0.000000] Calgary: Unable to locate Rio Grande table in EBDA - bailing!
[ 0.000000] Memory: 8084612k/9428992k available (7176k kernel code, 1107652k absent, 236728k reserved, 6067k data, 1016k init)
[ 0.000000] SLUB: Genslabs=15, HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU dyntick-idle grace-period acceleration is enabled.
[ 0.000000] RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=8.
[ 0.000000] NR_IRQS:16640 nr_irqs:744 16
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] allocated 33554432 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] hpet clockevent registered
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.004000] tsc: Detected 2095.333 MHz processor
[ 0.000002] Calibrating delay loop (skipped), value calculated using timer frequency.. 4190.66 BogoMIPS (lpj=8381332)
[ 0.000005] pid_max: default: 32768 minimum: 301
[ 0.000029] Security Framework initialized
[ 0.000041] AppArmor: AppArmor initialized
[ 0.000042] Yama: becoming mindful.
[ 0.000657] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.002502] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.003294] Mount-cache hash table entries: 256
[ 0.003468] Initializing cgroup subsys cpuacct
[ 0.003470] Initializing cgroup subsys memory
[ 0.003477] Initializing cgroup subsys devices
[ 0.003478] Initializing cgroup subsys freezer
[ 0.003480] Initializing cgroup subsys blkio
[ 0.003481] Initializing cgroup subsys perf_event
[ 0.003484] Initializing cgroup subsys hugetlb
[ 0.003508] CPU: Physical Processor ID: 0
[ 0.003509] CPU: Processor Core ID: 0
[ 0.003514] ENERGY_PERF_BIAS: Set to 'normal', was 'performance'
[ 0.003514] ENERGY_PERF_BIAS: View and update with x86_energy_perf_policy(8)
[ 0.003517] mce: CPU supports 7 MCE banks
[ 0.003529] CPU0: Thermal monitoring enabled (TM1)
[ 0.003537] process: using mwait in idle threads
[ 0.003540] Last level iTLB entries: 4KB 512, 2MB 0, 4MB 0
[ 0.003540] Last level dTLB entries: 4KB 512, 2MB 32, 4MB 32
[ 0.003540] tlb_flushall_shift: 5
[ 0.003686] Freeing SMP alternatives: 24k freed
[ 0.006575] ACPI: Core revision 20121018
[ 0.028086] ftrace: allocating 29399 entries in 115 pages
[ 0.044984] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.084613] smpboot: CPU0: Intel(R) Core(TM) i3-2310M CPU @ 2.10GHz (fam: 06, model: 2a, stepping: 07)
[ 0.084623] TSC deadline timer enabled
[ 0.084627] Performance Events: PEBS fmt1+, 16-deep LBR, SandyBridge events, Intel PMU driver.
[ 0.084634] perf_event_intel: PEBS disabled due to CPU errata, please upgrade microcode
[ 0.084636] ... version: 3
[ 0.084637] ... bit width: 48
[ 0.084638] ... generic registers: 4
[ 0.084640] ... value mask: 0000ffffffffffff
[ 0.084641] ... max period: 000000007fffffff
[ 0.084642] ... fixed-purpose events: 3
[ 0.084643] ... event mask: 000000070000000f
[ 0.099064] NMI watchdog: enabled on all CPUs, permanently consumes one hw-PMU counter.
[ 0.085857] smpboot: Booting Node 0, Processors #1 #2 #3
[ 0.125392] Brought up 4 CPUs
[ 0.125397] smpboot: Total of 4 processors activated (16762.66 BogoMIPS)
[ 0.129326] devtmpfs: initialized
[ 0.130427] EVM: security.selinux
[ 0.130429] EVM: security.SMACK64
[ 0.130430] EVM: security.capability
[ 0.130478] PM: Registering ACPI NVS region [mem 0xbcec0000-0xbcfbffff] (1048576 bytes)
[ 0.131285] regulator-dummy: no parameters
[ 0.131333] NET: Registered protocol family 16
[ 0.131482] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.131484] ACPI: bus type pci registered
[ 0.131552] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.131555] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in E820
[ 0.155605] PCI: Using configuration type 1 for base access
[ 0.156538] bio: create slab <bio-0> at 0
[ 0.156625] ACPI: Added _OSI(Module Device)
[ 0.156627] ACPI: Added _OSI(Processor Device)
[ 0.156628] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.156630] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.158604] ACPI: EC: Look up EC in DSDT
[ 0.160887] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.169048] [Firmware Bug]: ACPI: BIOS _OSI(Linux) query ignored
[ 0.191413] ACPI: SSDT 00000000bce69718 0069C (v01 PmRef Cpu0Cst 00003001 INTL 20060912)
[ 0.191914] ACPI: Dynamic OEM Table Load:
[ 0.191917] ACPI: SSDT (null) 0069C (v01 PmRef Cpu0Cst 00003001 INTL 20060912)
[ 0.192186] ACPI: SSDT 00000000bce6aa98 00303 (v01 PmRef ApIst 00003000 INTL 20060912)
[ 0.192717] ACPI: Dynamic OEM Table Load:
[ 0.192720] ACPI: SSDT (null) 00303 (v01 PmRef ApIst 00003000 INTL 20060912)
[ 0.192846] ACPI: SSDT 00000000bce68d98 00119 (v01 PmRef ApCst 00003000 INTL 20060912)
[ 0.193346] ACPI: Dynamic OEM Table Load:
[ 0.193348] ACPI: SSDT (null) 00119 (v01 PmRef ApCst 00003000 INTL 20060912)
[ 0.622028] ACPI: Interpreter enabled
[ 0.622032] ACPI: (supports S0 S3 S4 S5)
[ 0.622052] ACPI: Using IOAPIC for interrupt routing
[ 0.622912] ACPI: Power Resource [APPR] (off)
[ 0.626717] ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
[ 0.626866] ACPI: No dock devices found.
[ 0.626870] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.627157] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.627160] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.628233] PCI host bridge to bus 0000:00
[ 0.628236] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.628238] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7]
[ 0.628241] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff]
[ 0.628243] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff]
[ 0.628245] pci_bus 0000:00: root bus resource [mem 0xbfa00000-0xdfffffff]
[ 0.628246] pci_bus 0000:00: root bus resource [mem 0xf0000000-0xfedfffff]
[ 0.628248] pci_bus 0000:00: root bus resource [mem 0xfee01000-0xffffffff]
[ 0.628258] pci 0000:00:00.0: [8086:0104] type 00 class 0x060000
[ 0.628299] pci 0000:00:02.0: [8086:0116] type 00 class 0x030000
[ 0.628311] pci 0000:00:02.0: reg 10: [mem 0xd4000000-0xd43fffff 64bit]
[ 0.628318] pci 0000:00:02.0: reg 18: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.628323] pci 0000:00:02.0: reg 20: [io 0x5000-0x503f]
[ 0.628382] pci 0000:00:16.0: [8086:1c3a] type 00 class 0x078000
[ 0.628407] pci 0000:00:16.0: reg 10: [mem 0xd4a04000-0xd4a0400f 64bit]
[ 0.628487] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.628526] pci 0000:00:1a.0: [8086:1c2d] type 00 class 0x0c0320
[ 0.628550] pci 0000:00:1a.0: reg 10: [mem 0xd4a09000-0xd4a093ff]
[ 0.628652] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.628681] pci 0000:00:1b.0: [8086:1c20] type 00 class 0x040300
[ 0.628699] pci 0000:00:1b.0: reg 10: [mem 0xd4a00000-0xd4a03fff 64bit]
[ 0.628773] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.628799] pci 0000:00:1c.0: [8086:1c10] type 01 class 0x060400
[ 0.628885] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.628913] pci 0000:00:1c.1: [8086:1c12] type 01 class 0x060400
[ 0.629001] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.629030] pci 0000:00:1c.2: [8086:1c14] type 01 class 0x060400
[ 0.629114] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.629144] pci 0000:00:1c.3: [8086:1c16] type 01 class 0x060400
[ 0.629229] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.629259] pci 0000:00:1c.5: [8086:1c1a] type 01 class 0x060400
[ 0.629342] pci 0000:00:1c.5: PME# supported from D0 D3hot D3cold
[ 0.629373] pci 0000:00:1c.7: [8086:1c1e] type 01 class 0x060400
[ 0.629456] pci 0000:00:1c.7: PME# supported from D0 D3hot D3cold
[ 0.629488] pci 0000:00:1d.0: [8086:1c26] type 00 class 0x0c0320
[ 0.629512] pci 0000:00:1d.0: reg 10: [mem 0xd4a08000-0xd4a083ff]
[ 0.629608] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.629637] pci 0000:00:1f.0: [8086:1c49] type 00 class 0x060100
[ 0.629770] pci 0000:00:1f.2: [8086:1c03] type 00 class 0x010601
[ 0.629791] pci 0000:00:1f.2: reg 10: [io 0x5068-0x506f]
[ 0.629800] pci 0000:00:1f.2: reg 14: [io 0x5074-0x5077]
[ 0.629809] pci 0000:00:1f.2: reg 18: [io 0x5060-0x5067]
[ 0.629818] pci 0000:00:1f.2: reg 1c: [io 0x5070-0x5073]
[ 0.629827] pci 0000:00:1f.2: reg 20: [io 0x5040-0x505f]
[ 0.629837] pci 0000:00:1f.2: reg 24: [mem 0xd4a07000-0xd4a077ff]
[ 0.629885] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.629958] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.629965] pci 0000:00:1c.0: bridge window [mem 0xd4900000-0xd49fffff]
[ 0.630018] pci 0000:00:1c.1: PCI bridge to [bus 02-22]
[ 0.630023] pci 0000:00:1c.1: bridge window [io 0x3000-0x4fff]
[ 0.630027] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd3ffffff]
[ 0.630104] pci 0000:23:00.0: [197b:2392] type 00 class 0x088000
[ 0.630131] pci 0000:23:00.0: reg 10: [mem 0xd4803000-0xd48030ff]
[ 0.630242] pci 0000:23:00.0: reg 30: [mem 0xffff0000-0xffffffff pref]
[ 0.630389] pci 0000:23:00.2: [197b:2391] type 00 class 0x080501
[ 0.630416] pci 0000:23:00.2: reg 10: [mem 0xd4802000-0xd48020ff]
[ 0.630668] pci 0000:23:00.3: [197b:2393] type 00 class 0x088000
[ 0.630696] pci 0000:23:00.3: reg 10: [mem 0xd4801000-0xd48010ff]
[ 0.640702] pci 0000:00:1c.2: PCI bridge to [bus 23]
[ 0.640718] pci 0000:00:1c.2: bridge window [mem 0xd4800000-0xd48fffff]
[ 0.640851] pci 0000:24:00.0: [168c:002b] type 00 class 0x028000
[ 0.640880] pci 0000:24:00.0: reg 10: [mem 0xd4700000-0xd470ffff 64bit]
[ 0.641016] pci 0000:24:00.0: supports D1
[ 0.641018] pci 0000:24:00.0: PME# supported from D0 D1 D3hot
[ 0.652660] pci 0000:00:1c.3: PCI bridge to [bus 24]
[ 0.652674] pci 0000:00:1c.3: bridge window [mem 0xd4700000-0xd47fffff]
[ 0.652875] pci 0000:25:00.0: [10ec:8168] type 00 class 0x020000
[ 0.652945] pci 0000:25:00.0: reg 10: [io 0x2000-0x20ff]
[ 0.653067] pci 0000:25:00.0: reg 18: [mem 0xd4404000-0xd4404fff 64bit pref]
[ 0.653142] pci 0000:25:00.0: reg 20: [mem 0xd4400000-0xd4403fff 64bit pref]
[ 0.653476] pci 0000:25:00.0: supports D1 D2
[ 0.653478] pci 0000:25:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.664672] pci 0000:00:1c.5: PCI bridge to [bus 25]
[ 0.664682] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
[ 0.664692] pci 0000:00:1c.5: bridge window [mem 0xd4600000-0xd46fffff]
[ 0.664707] pci 0000:00:1c.5: bridge window [mem 0xd4400000-0xd44fffff 64bit pref]
[ 0.664854] pci 0000:26:00.0: [1033:0194] type 00 class 0x0c0330
[ 0.664902] pci 0000:26:00.0: reg 10: [mem 0xd4500000-0xd4501fff 64bit]
[ 0.665092] pci 0000:26:00.0: PME# supported from D0 D3hot D3cold
[ 0.676651] pci 0000:00:1c.7: PCI bridge to [bus 26]
[ 0.676666] pci 0000:00:1c.7: bridge window [mem 0xd4500000-0xd45fffff]
[ 0.676807] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.676845] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.676901] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.676950] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP04._PRT]
[ 0.676984] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP06._PRT]
[ 0.677022] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP08._PRT]
[ 0.677431] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.678592] pci0000:00: ACPI _OSC control (0x1d) granted
[ 0.679366] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.679411] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15)
[ 0.679453] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.679493] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
[ 0.679534] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.679576] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.679619] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.679660] ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.679759] vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.679763] vgaarb: loaded
[ 0.679764] vgaarb: bridge control possible 0000:00:02.0
[ 0.679927] SCSI subsystem initialized
[ 0.679930] ACPI: bus type scsi registered
[ 0.679979] libata version 3.00 loaded.
[ 0.679994] ACPI: bus type usb registered
[ 0.680009] usbcore: registered new interface driver usbfs
[ 0.680018] usbcore: registered new interface driver hub
[ 0.680039] usbcore: registered new device driver usb
[ 0.680119] PCI: Using ACPI for IRQ routing
[ 0.687182] PCI: pci_cache_line_size set to 64 bytes
[ 0.687273] e820: reserve RAM buffer [mem 0x0009ec00-0x0009ffff]
[ 0.687275] e820: reserve RAM buffer [mem 0xbc6c0000-0xbfffffff]
[ 0.687277] e820: reserve RAM buffer [mem 0xbd000000-0xbfffffff]
[ 0.687278] e820: reserve RAM buffer [mem 0x23f800000-0x23fffffff]
[ 0.687361] NetLabel: Initializing
[ 0.687362] NetLabel: domain hash size = 128
[ 0.687363] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.687375] NetLabel: unlabeled traffic allowed by default
[ 0.687430] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0, 0, 0, 0, 0, 0
[ 0.687436] hpet0: 8 comparators, 64-bit 14.318180 MHz counter
[ 0.689447] Switching to clocksource hpet
[ 0.694584] AppArmor: AppArmor Filesystem Enabled
[ 0.694610] pnp: PnP ACPI init
[ 0.694621] ACPI: bus type pnp registered
[ 0.694783] system 00:00: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.694786] system 00:00: [mem 0xfed10000-0xfed17fff] could not be reserved
[ 0.694788] system 00:00: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.694790] system 00:00: [mem 0x00000000-0x00000fff] could not be reserved
[ 0.694793] system 00:00: [mem 0xbfa00000-0xbfa00fff] has been reserved
[ 0.694795] system 00:00: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.694797] system 00:00: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.694799] system 00:00: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.694801] system 00:00: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.694803] system 00:00: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.694807] system 00:00: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.694879] pnp 00:01: [dma 4]
[ 0.694899] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.694920] pnp 00:02: Plug and Play ACPI device, IDs INT0800 (active)
[ 0.694973] system 00:03: [io 0xfe00-0xfe0f] has been reserved
[ 0.694976] system 00:03: [io 0xfe80-0xfe8f] has been reserved
[ 0.694978] system 00:03: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.694981] system 00:03: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.695085] pnp 00:04: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.695120] pnp 00:05: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.695159] system 00:06: [io 0x0200-0x027f] has been reserved
[ 0.695162] system 00:06: [io 0x1000-0x100f] has been reserved
[ 0.695164] system 00:06: [io 0xffff] has been reserved
[ 0.695166] system 00:06: [io 0xffff] has been reserved
[ 0.695168] system 00:06: [io 0x0400-0x047f] has been reserved
[ 0.695170] system 00:06: [io 0x0500-0x057f] has been reserved
[ 0.695172] system 00:06: [io 0xef80-0xef9f] has been reserved
[ 0.695175] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.695201] pnp 00:07: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.695323] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.695353] pnp 00:09: Plug and Play ACPI device, IDs SYN0185 SYN0100 SYN0002 PNP0f13 (active)
[ 0.695592] pnp 00:0a: Plug and Play ACPI device, IDs HPQ0004 (active)
[ 0.695771] pnp: PnP ACPI: found 11 devices
[ 0.695773] ACPI: ACPI bus type pnp unregistered
[ 0.701902] pci 0000:23:00.0: no compatible bridge window for [mem 0xffff0000-0xffffffff pref]
[ 0.701930] pci 0000:00:1c.1: bridge window [mem 0x00100000-0x000fffff 64bit pref] to [bus 02-22] add_size 200000
[ 0.701967] pci 0000:00:1c.1: res[15]=[mem 0x00100000-0x000fffff 64bit pref] get_res_add_size add_size 200000
[ 0.701972] pci 0000:00:1c.1: BAR 15: assigned [mem 0xbfb00000-0xbfcfffff 64bit pref]
[ 0.701975] pci 0000:00:1c.2: BAR 15: assigned [mem 0xbfd00000-0xbfdfffff pref]
[ 0.701977] pci 0000:00:1c.0: PCI bridge to [bus 01]
[ 0.701984] pci 0000:00:1c.0: bridge window [mem 0xd4900000-0xd49fffff]
[ 0.701993] pci 0000:00:1c.1: PCI bridge to [bus 02-22]
[ 0.701997] pci 0000:00:1c.1: bridge window [io 0x3000-0x4fff]
[ 0.702003] pci 0000:00:1c.1: bridge window [mem 0xd0000000-0xd3ffffff]
[ 0.702008] pci 0000:00:1c.1: bridge window [mem 0xbfb00000-0xbfcfffff 64bit pref]
[ 0.702016] pci 0000:23:00.0: BAR 6: assigned [mem 0xbfd00000-0xbfd0ffff pref]
[ 0.702018] pci 0000:00:1c.2: PCI bridge to [bus 23]
[ 0.702024] pci 0000:00:1c.2: bridge window [mem 0xd4800000-0xd48fffff]
[ 0.702028] pci 0000:00:1c.2: bridge window [mem 0xbfd00000-0xbfdfffff pref]
[ 0.702035] pci 0000:00:1c.3: PCI bridge to [bus 24]
[ 0.702041] pci 0000:00:1c.3: bridge window [mem 0xd4700000-0xd47fffff]
[ 0.702050] pci 0000:00:1c.5: PCI bridge to [bus 25]
[ 0.702053] pci 0000:00:1c.5: bridge window [io 0x2000-0x2fff]
[ 0.702059] pci 0000:00:1c.5: bridge window [mem 0xd4600000-0xd46fffff]
[ 0.702064] pci 0000:00:1c.5: bridge window [mem 0xd4400000-0xd44fffff 64bit pref]
[ 0.702071] pci 0000:00:1c.7: PCI bridge to [bus 26]
[ 0.702076] pci 0000:00:1c.7: bridge window [mem 0xd4500000-0xd45fffff]
[ 0.702130] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.702132] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.702134] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.702136] pci_bus 0000:00: resource 7 [mem 0xbfa00000-0xdfffffff]
[ 0.702138] pci_bus 0000:00: resource 8 [mem 0xf0000000-0xfedfffff]
[ 0.702140] pci_bus 0000:00: resource 9 [mem 0xfee01000-0xffffffff]
[ 0.702142] pci_bus 0000:01: resource 1 [mem 0xd4900000-0xd49fffff]
[ 0.702144] pci_bus 0000:02: resource 0 [io 0x3000-0x4fff]
[ 0.702146] pci_bus 0000:02: resource 1 [mem 0xd0000000-0xd3ffffff]
[ 0.702148] pci_bus 0000:02: resource 2 [mem 0xbfb00000-0xbfcfffff 64bit pref]
[ 0.702150] pci_bus 0000:23: resource 1 [mem 0xd4800000-0xd48fffff]
[ 0.702152] pci_bus 0000:23: resource 2 [mem 0xbfd00000-0xbfdfffff pref]
[ 0.702154] pci_bus 0000:24: resource 1 [mem 0xd4700000-0xd47fffff]
[ 0.702156] pci_bus 0000:25: resource 0 [io 0x2000-0x2fff]
[ 0.702158] pci_bus 0000:25: resource 1 [mem 0xd4600000-0xd46fffff]
[ 0.702160] pci_bus 0000:25: resource 2 [mem 0xd4400000-0xd44fffff 64bit pref]
[ 0.702162] pci_bus 0000:26: resource 1 [mem 0xd4500000-0xd45fffff]
[ 0.702192] NET: Registered protocol family 2
[ 0.702374] TCP established hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.702597] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.702734] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.702759] TCP: reno registered
[ 0.702775] UDP hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.702809] UDP-Lite hash table entries: 4096 (order: 5, 131072 bytes)
[ 0.702890] NET: Registered protocol family 1
[ 0.702904] pci 0000:00:02.0: Boot video device
[ 0.703054] PCI: CLS 64 bytes, default 64
[ 0.703096] Trying to unpack rootfs image as initramfs...
[ 1.102606] Freeing initrd memory: 22276k freed
[ 1.105551] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 1.105557] software IO TLB [mem 0xb86ba000-0xbc6ba000] (64MB) mapped at [ffff8800b86ba000-ffff8800bc6b9fff]
[ 1.105956] Initialise module verification
[ 1.106000] audit: initializing netlink socket (disabled)
[ 1.106010] type=2000 audit(1389775038.096:1): initialized
[ 1.139600] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 1.141050] VFS: Disk quotas dquot_6.5.2
[ 1.141092] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 1.141522] fuse init (API version 7.20)
[ 1.141588] msgmni has been set to 15833
[ 1.142037] Key type asymmetric registered
[ 1.142040] Asymmetric key parser 'x509' registered
[ 1.142069] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 1.142098] io scheduler noop registered
[ 1.142101] io scheduler deadline registered (default)
[ 1.142106] io scheduler cfq registered
[ 1.142243] pcieport 0000:00:1c.0: irq 40 for MSI/MSI-X
[ 1.142354] pcieport 0000:00:1c.1: irq 41 for MSI/MSI-X
[ 1.142465] pcieport 0000:00:1c.2: irq 42 for MSI/MSI-X
[ 1.142566] pcieport 0000:00:1c.3: irq 43 for MSI/MSI-X
[ 1.142668] pcieport 0000:00:1c.5: irq 44 for MSI/MSI-X
[ 1.142769] pcieport 0000:00:1c.7: irq 45 for MSI/MSI-X
[ 1.142853] pcieport 0000:00:1c.0: Signaling PME through PCIe PME interrupt
[ 1.142858] pcie_pme 0000:00:1c.0:pcie01: service driver pcie_pme loaded
[ 1.142876] pcieport 0000:00:1c.1: Signaling PME through PCIe PME interrupt
[ 1.142881] pcie_pme 0000:00:1c.1:pcie01: service driver pcie_pme loaded
[ 1.142898] pcieport 0000:00:1c.2: Signaling PME through PCIe PME interrupt
[ 1.142900] pci 0000:23:00.0: Signaling PME through PCIe PME interrupt
[ 1.142902] pci 0000:23:00.2: Signaling PME through PCIe PME interrupt
[ 1.142904] pci 0000:23:00.3: Signaling PME through PCIe PME interrupt
[ 1.142909] pcie_pme 0000:00:1c.2:pcie01: service driver pcie_pme loaded
[ 1.142927] pcieport 0000:00:1c.3: Signaling PME through PCIe PME interrupt
[ 1.142929] pci 0000:24:00.0: Signaling PME through PCIe PME interrupt
[ 1.142934] pcie_pme 0000:00:1c.3:pcie01: service driver pcie_pme loaded
[ 1.142951] pcieport 0000:00:1c.5: Signaling PME through PCIe PME interrupt
[ 1.142953] pci 0000:25:00.0: Signaling PME through PCIe PME interrupt
[ 1.142958] pcie_pme 0000:00:1c.5:pcie01: service driver pcie_pme loaded
[ 1.142975] pcieport 0000:00:1c.7: Signaling PME through PCIe PME interrupt
[ 1.142977] pci 0000:26:00.0: Signaling PME through PCIe PME interrupt
[ 1.142981] pcie_pme 0000:00:1c.7:pcie01: service driver pcie_pme loaded
[ 1.142993] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 1.143047] pciehp 0000:00:1c.1:pcie04: HPC vendor_id 8086 device_id 1c12 ss_vid 103c ss_did 167c
[ 1.143071] pciehp 0000:00:1c.1:pcie04: service driver pciehp loaded
[ 1.143077] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[ 1.143113] intel_idle: MWAIT substates: 0x21120
[ 1.143114] intel_idle: v0.4 model 0x2A
[ 1.143116] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 1.143313] ACPI: AC Adapter [AC] (on-line)
[ 1.143494] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input0
[ 1.143499] ACPI: Sleep Button [SLPB]
[ 1.143530] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input1
[ 1.143551] ACPI: Lid Switch [LID]
[ 1.143584] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input2
[ 1.143587] ACPI: Power Button [PWRF]
[ 1.143649] ACPI: Requesting acpi_cpufreq
[ 1.172795] thermal LNXTHERM:00: registered as thermal_zone0
[ 1.172798] ACPI: Thermal Zone [CPUZ] (53 C)
[ 1.197629] thermal LNXTHERM:01: registered as thermal_zone1
[ 1.197631] ACPI: Thermal Zone [GFXZ] (0 C)
[ 1.219428] thermal LNXTHERM:02: registered as thermal_zone2
[ 1.219430] ACPI: Thermal Zone [EXTZ] (46 C)
[ 1.234277] thermal LNXTHERM:03: registered as thermal_zone3
[ 1.234279] ACPI: Thermal Zone [LOCZ] (43 C)
[ 1.250182] thermal LNXTHERM:04: registered as thermal_zone4
[ 1.250184] ACPI: Thermal Zone [BATZ] (28 C)
[ 1.250472] thermal LNXTHERM:05: registered as thermal_zone5
[ 1.250473] ACPI: Thermal Zone [PCHZ] (0 C)
[ 1.250566] thermal LNXTHERM:06: registered as thermal_zone6
[ 1.250568] ACPI: Thermal Zone [DM1Z] (0 C)
[ 1.250655] thermal LNXTHERM:07: registered as thermal_zone7
[ 1.250657] ACPI: Thermal Zone [DM2Z] (0 C)
[ 1.250687] GHES: HEST is not enabled!
[ 1.250765] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
[ 1.252161] Linux agpgart interface v0.103
[ 1.253376] brd: module loaded
[ 1.254014] loop: module loaded
[ 1.254292] libphy: Fixed MDIO Bus: probed
[ 1.254344] tun: Universal TUN/TAP device driver, 1.6
[ 1.254345] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 1.254387] PPP generic driver version 2.4.2
[ 1.254440] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.254442] ehci-pci: EHCI PCI platform driver
[ 1.254480] ehci-pci 0000:00:1a.0: setting latency timer to 64
[ 1.254484] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 1.254489] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 1.254504] ehci-pci 0000:00:1a.0: debug port 2
[ 1.258395] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 1.258414] ehci-pci 0000:00:1a.0: irq 16, io mem 0xd4a09000
[ 1.268627] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 1.268683] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.268689] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.268694] usb usb1: Product: EHCI Host Controller
[ 1.268699] usb usb1: Manufacturer: Linux 3.8.0-35-generic ehci_hcd
[ 1.268704] usb usb1: SerialNumber: 0000:00:1a.0
[ 1.268902] hub 1-0:1.0: USB hub found
[ 1.268907] hub 1-0:1.0: 2 ports detected
[ 1.269028] ehci-pci 0000:00:1d.0: setting latency timer to 64
[ 1.269032] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 1.269037] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 1.269049] ehci-pci 0000:00:1d.0: debug port 2
[ 1.272928] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 1.272934] ehci-pci 0000:00:1d.0: irq 16, io mem 0xd4a08000
[ 1.284594] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 1.284639] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.284645] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.284650] usb usb2: Product: EHCI Host Controller
[ 1.284655] usb usb2: Manufacturer: Linux 3.8.0-35-generic ehci_hcd
[ 1.284660] usb usb2: SerialNumber: 0000:00:1d.0
[ 1.284827] hub 2-0:1.0: USB hub found
[ 1.284833] hub 2-0:1.0: 2 ports detected
[ 1.284989] ehci-platform: EHCI generic platform driver
[ 1.284995] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 1.285008] uhci_hcd: USB Universal Host Controller Interface driver
[ 1.285045] xhci_hcd 0000:26:00.0: xHCI Host Controller
[ 1.285050] xhci_hcd 0000:26:00.0: new USB bus registered, assigned bus number 3
[ 1.285269] xhci_hcd 0000:26:00.0: irq 46 for MSI/MSI-X
[ 1.285275] xhci_hcd 0000:26:00.0: irq 47 for MSI/MSI-X
[ 1.285281] xhci_hcd 0000:26:00.0: irq 48 for MSI/MSI-X
[ 1.285286] xhci_hcd 0000:26:00.0: irq 49 for MSI/MSI-X
[ 1.285292] xhci_hcd 0000:26:00.0: irq 50 for MSI/MSI-X
[ 1.285399] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.285402] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.285403] usb usb3: Product: xHCI Host Controller
[ 1.285405] usb usb3: Manufacturer: Linux 3.8.0-35-generic xhci_hcd
[ 1.285407] usb usb3: SerialNumber: 0000:26:00.0
[ 1.285468] xHCI xhci_add_endpoint called for root hub
[ 1.285470] xHCI xhci_check_bandwidth called for root hub
[ 1.285489] hub 3-0:1.0: USB hub found
[ 1.285496] hub 3-0:1.0: 2 ports detected
[ 1.285555] xhci_hcd 0000:26:00.0: xHCI Host Controller
[ 1.285558] xhci_hcd 0000:26:00.0: new USB bus registered, assigned bus number 4
[ 1.288663] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 1.288666] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.288667] usb usb4: Product: xHCI Host Controller
[ 1.288669] usb usb4: Manufacturer: Linux 3.8.0-35-generic xhci_hcd
[ 1.288671] usb usb4: SerialNumber: 0000:26:00.0
[ 1.288741] xHCI xhci_add_endpoint called for root hub
[ 1.288742] xHCI xhci_check_bandwidth called for root hub
[ 1.288759] hub 4-0:1.0: USB hub found
[ 1.288767] hub 4-0:1.0: 2 ports detected
[ 1.288900] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 1.290840] i8042: Detected active multiplexing controller, rev 1.1
[ 1.291604] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.291610] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 1.291630] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 1.291646] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 1.291660] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 1.291746] mousedev: PS/2 mouse device common for all mice
[ 1.291876] rtc_cmos 00:07: RTC can wake from S4
[ 1.291991] rtc_cmos 00:07: rtc core: registered rtc_cmos as rtc0
[ 1.292020] rtc0: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 1.292098] device-mapper: uevent: version 1.0.3
[ 1.292148] device-mapper: ioctl: 4.23.1-ioctl (2012-12-18) initialised: dm-devel@redhat.com
[ 1.292219] cpuidle: using governor ladder
[ 1.292311] cpuidle: using governor menu
[ 1.292316] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.292317] EFI Variables Facility v0.08 2004-May-17
[ 1.292481] ashmem: initialized
[ 1.292597] TCP: cubic registered
[ 1.292677] NET: Registered protocol family 10
[ 1.292832] NET: Registered protocol family 17
[ 1.292845] Key type dns_resolver registered
[ 1.293039] Loading module verification certificates
[ 1.294041] MODSIGN: Loaded cert 'Magrathea: Glacier signing key: 26d22696497e0146aec821b3bfa3dd9972acd4d9'
[ 1.294052] registered taskstats version 1
[ 1.295124] ACPI: Battery Slot [BAT0] (battery present)
[ 1.296201] Key type trusted registered
[ 1.297834] Key type encrypted registered
[ 1.299943] rtc_cmos 00:07: setting system clock to 2014-01-15 08:37:19 UTC (1389775039)
[ 1.300545] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[ 1.300562] EDD information not available.
[ 1.302291] Freeing unused kernel memory: 1016k freed
[ 1.302426] Write protecting the kernel read-only data: 12288k
[ 1.305637] Freeing unused kernel memory: 1004k freed
[ 1.308718] Freeing unused kernel memory: 952k freed
[ 1.313696] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[ 1.325492] udevd[111]: starting version 175
[ 1.354189] Disabling lock debugging due to kernel taint
[ 1.354541] sdhci: Secure Digital Host Controller Interface driver
[ 1.354544] sdhci: Copyright(c) Pierre Ossman
[ 1.354918] sdhci-pci 0000:23:00.0: SDHCI controller found [197b:2392] (rev 30)
[ 1.354980] mmc0: no vqmmc regulator found
[ 1.354983] mmc0: no vmmc regulator found
[ 1.358049] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 1.358272] r8169 0000:25:00.0: irq 51 for MSI/MSI-X
[ 1.358426] r8169 0000:25:00.0 eth0: RTL8168e/8111e at 0xffffc90000c3c000, 64:31:50:8f:c6:d1, XID 0c200000 IRQ 51
[ 1.358429] r8169 0000:25:00.0 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 1.358563] ahci 0000:00:1f.2: version 3.0
[ 1.358624] ahci 0000:00:1f.2: irq 52 for MSI/MSI-X
[ 1.358665] ahci: SSS flag set, parallel bus scan disabled
[ 1.358695] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x3 impl SATA mode
[ 1.358699] ahci 0000:00:1f.2: flags: 64bit ncq sntf stag pm led clo pio slum part ems apst
[ 1.358703] ahci 0000:00:1f.2: setting latency timer to 64
[ 1.363893] [drm] Initialized drm 1.1.0 20060810
[ 1.368213] scsi0 : ahci
[ 1.369837] scsi1 : ahci
[ 1.369952] scsi2 : ahci
[ 1.370024] scsi3 : ahci
[ 1.370107] scsi4 : ahci
[ 1.370176] scsi5 : ahci
[ 1.370264] ata1: SATA max UDMA/133 abar m2048@0xd4a07000 port 0xd4a07100 irq 52
[ 1.370268] ata2: SATA max UDMA/133 abar m2048@0xd4a07000 port 0xd4a07180 irq 52
[ 1.370270] ata3: DUMMY
[ 1.370271] ata4: DUMMY
[ 1.370272] ata5: DUMMY
[ 1.370273] ata6: DUMMY
[ 1.371671] [drm] Memory usable by graphics device = 2048M
[ 1.371681] i915 0000:00:02.0: setting latency timer to 64
[ 1.381105] wmi: Mapper loaded
[ 1.385542] mmc0: SDHCI controller on PCI [0000:23:00.0] using DMA
[ 1.385566] sdhci-pci 0000:23:00.2: SDHCI controller found [197b:2391] (rev 30)
[ 1.385588] sdhci-pci 0000:23:00.2: Refusing to bind to secondary interface.
[ 1.416139] i915 0000:00:02.0: irq 53 for MSI/MSI-X
[ 1.416153] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 1.416156] [drm] Driver supports precise vblank timestamp query.
[ 1.416201] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 1.580215] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 1.636395] fbcon: inteldrmfb (fb0) is primary device
[ 1.688097] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 1.688882] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 1.688925] ata1.00: ATA-9: OCZ-VERTEX4, 1.5, max UDMA/133
[ 1.688926] ata1.00: 250069680 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 1.689676] ata1.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 1.689713] ata1.00: configured for UDMA/133
[ 1.696362] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX4 1.5 PQ: 0 ANSI: 5
[ 1.696522] sd 0:0:0:0: [sda] 250069680 512-byte logical blocks: (128 GB/119 GiB)
[ 1.696559] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.696597] sd 0:0:0:0: [sda] Write Protect is off
[ 1.696600] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.696626] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.697279] sda: sda1 sda2 sda3 < sda5 > sda4
[ 1.697694] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.712609] usb 1-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.712614] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.712812] hub 1-1:1.0: USB hub found
[ 1.712938] hub 1-1:1.0: 6 ports detected
[ 1.823893] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 1.956078] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.956080] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.956363] hub 2-1:1.0: USB hub found
[ 1.956422] hub 2-1:1.0: 6 ports detected
[ 2.015601] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 2.020721] ata2.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 2.020763] ata2.00: ATAPI: HL-DT-ST DVDRAM GT60N, 1.00, max UDMA/133
[ 2.027761] usb 1-1.3: new low-speed USB device number 3 using ehci-pci
[ 2.027833] ata2.00: ACPI cmd 00/00:00:00:00:00:a0 (NOP) rejected by device (Stat=0x51 Err=0x04)
[ 2.027853] ata2.00: configured for UDMA/133
[ 2.033629] scsi 1:0:0:0: CD-ROM HL-DT-ST DVDRAM GT60N 1.00 PQ: 0 ANSI: 5
[ 2.040172] sr0: scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 2.040174] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 2.040352] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 2.040437] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.103411] tsc: Refined TSC clocksource calibration: 2095.240 MHz
[ 2.103418] Switching to clocksource tsc
[ 2.183715] usb 1-1.3: New USB device found, idVendor=04f3, idProduct=00a4
[ 2.183719] usb 1-1.3: New USB device strings: Mfr=0, Product=2, SerialNumber=0
[ 2.183723] usb 1-1.3: Product: 2.4G RX
[ 2.255227] usb 2-1.4: new high-speed USB device number 3 using ehci-pci
[ 2.263840] usbcore: registered new interface driver usbhid
[ 2.263843] usbhid: USB HID core driver
[ 2.265836] input: 2.4G RX as /devices/pci0000:00/0000:00:1a.0/usb1/1-1/1-1.3/1-1.3:1.0/input/input4
[ 2.265992] hid-generic 0003:04F3:00A4.0001: input,hidraw0: USB HID v1.10 Keyboard [2.4G RX] on usb-0000:00:1a.0-1.3/input0
[ 2.275246] Console: switching to colour frame buffer device 170x48
[ 2.278007] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 2.278009] i915 0000:00:02.0: registered panic notifier
[ 2.282459] acpi device:03: registered as cooling_device4
[ 2.282638] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 2.282684] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:00/input/input5
[ 2.282894] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 2.477538] usb 2-1.4: New USB device found, idVendor=1bcf, idProduct=2805
[ 2.477543] usb 2-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 2.477545] usb 2-1.4: Product: HP HD Webcam [Fixed]
[ 2.477547] usb 2-1.4: Manufacturer: Sunplus IT Co
[ 2.571941] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: (null)
[ 2.718691] usb 2-1.6: new full-speed USB device number 4 using ehci-pci
[ 2.750283] init: ureadahead main process (374) terminated with status 5
[ 2.798308] Adding 975868k swap on /dev/sda5. Priority:-1 extents:1 across:975868k SS
[ 2.802760] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 2.811054] usb 2-1.6: New USB device found, idVendor=03f0, idProduct=311d
[ 2.811059] usb 2-1.6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.824087] EXT4-fs (sda4): re-mounted. Opts: errors=remount-ro
[ 2.848863] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 2.858845] udevd[464]: starting version 175
[ 2.889060] lp: driver loaded but no devices found
[ 2.946142] hp_accel: laptop model unknown, using default axes configuration
[ 2.947414] lis3lv02d: 8 bits 3DC sensor found
[ 2.984753] ppdev: user-space parallel port driver
[ 2.998661] input: ST LIS3LV02DL Accelerometer as /devices/platform/lis3lv02d/input/input6
[ 3.002991] Bluetooth: Core ver 2.16
[ 3.003013] NET: Registered protocol family 31
[ 3.003015] Bluetooth: HCI device and connection manager initialized
[ 3.003024] Bluetooth: HCI socket layer initialized
[ 3.003028] Bluetooth: L2CAP socket layer initialized
[ 3.003036] Bluetooth: SCO socket layer initialized
[ 3.007278] mei 0000:00:16.0: setting latency timer to 64
[ 3.007357] mei 0000:00:16.0: irq 54 for MSI/MSI-X
[ 3.008217] Bluetooth: RFCOMM TTY layer initialized
[ 3.008230] Bluetooth: RFCOMM socket layer initialized
[ 3.008232] Bluetooth: RFCOMM ver 1.11
[ 3.011685] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 3.011690] Bluetooth: BNEP filters: protocol multicast
[ 3.011699] Bluetooth: BNEP socket layer initialized
[ 3.026342] type=1400 audit(1389771441.227:2): apparmor="STATUS" operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" pid=626 comm="apparmor_parser"
[ 3.026844] type=1400 audit(1389771441.227:3): apparmor="STATUS" operation="profile_load" name="/usr/sbin/cupsd" pid=626 comm="apparmor_parser"
[ 3.044413] cfg80211: Calling CRDA to update world regulatory domain
[ 3.056627] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20121018/utaddress-251)
[ 3.056636] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 3.056641] ACPI Warning: 0x0000000000000540-0x000000000000054f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[ 3.056646] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 3.056649] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[ 3.056654] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 3.056656] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20121018/utaddress-251)
[ 3.056660] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 3.056662] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 3.082745] type=1400 audit(1389771441.283:4): apparmor="STATUS" operation="profile_load" name="/sbin/dhclient" pid=667 comm="apparmor_parser"
[ 3.083225] type=1400 audit(1389771441.283:5): apparmor="STATUS" operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=667 comm="apparmor_parser"
[ 3.083501] type=1400 audit(1389771441.283:6): apparmor="STATUS" operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" pid=667 comm="apparmor_parser"
[ 3.095279] type=1400 audit(1389771441.295:7): apparmor="STATUS" operation="profile_load" name="/usr/sbin/ntpd" pid=668 comm="apparmor_parser"
[ 3.129721] ath: EEPROM regdomain: 0x60
[ 3.129725] ath: EEPROM indicates we should expect a direct regpair map
[ 3.129728] ath: Country alpha2 being used: 00
[ 3.129730] ath: Regpair used: 0x60
[ 3.138942] usbcore: registered new interface driver btusb
[ 3.146660] microcode: CPU0 sig=0x206a7, pf=0x10, revision=0x14
[ 3.155055] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 3.155478] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc90010ee0000, irq=19
[ 3.158562] Linux video capture interface: v2.00
[ 3.162995] uvcvideo: Found UVC 1.00 device HP HD Webcam [Fixed] (1bcf:2805)
[ 3.172954] snd_hda_intel 0000:00:1b.0: irq 55 for MSI/MSI-X
[ 3.180861] input: HP HD Webcam [Fixed] as /devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.4/2-1.4:1.0/input/input7
[ 3.180969] usbcore: registered new interface driver uvcvideo
[ 3.180972] USB Video Class driver (1.1.1)
[ 3.242624] input: HDA Intel PCH HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:1b.0/sound/card0/input8
[ 3.242840] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input9
[ 3.242962] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10
[ 3.263369] init: failsafe main process (755) killed by TERM signal
[ 3.297606] microcode: CPU1 sig=0x206a7, pf=0x10, revision=0x14
[ 3.339674] microcode: CPU2 sig=0x206a7, pf=0x10, revision=0x14
[ 3.340882] type=1400 audit(1389771441.539:8): apparmor="STATUS" operation="profile_replace" name="/sbin/dhclient" pid=916 comm="apparmor_parser"
[ 3.341356] type=1400 audit(1389771441.539:9): apparmor="STATUS" operation="profile_replace" name="/usr/lib/NetworkManager/nm-dhcp-client.action" pid=916 comm="apparmor_parser"
[ 3.342005] type=1400 audit(1389771441.543:10): apparmor="STATUS" operation="profile_replace" name="/usr/lib/connman/scripts/dhclient-script" pid=916 comm="apparmor_parser"
[ 3.344399] microcode: CPU3 sig=0x206a7, pf=0x10, revision=0x14
[ 3.352602] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 3.374755] kvm: disabled by bios
[ 3.389666] input: HP WMI hotkeys as /devices/virtual/input/input11
[ 3.408731] usbcore: registered new interface driver ath3k
[ 3.416311] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3.419484] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3.565069] r8169 0000:25:00.0 eth0: link down
[ 3.565103] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.565562] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3.575240] usb 2-1.6: USB disconnect, device number 4
[ 4.012583] psmouse serio4: synaptics: Touchpad model: 1, fw: 7.5, id: 0x1e0b1, caps: 0xd00073/0x640000/0xa0400, board id: 1397, fw id: 780218
[ 4.028585] usb 2-1.6: new full-speed USB device number 5 using ehci-pci
[ 4.057471] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio4/input/input12
[ 4.121338] usb 2-1.6: New USB device found, idVendor=0cf3, idProduct=3005
[ 4.121352] usb 2-1.6: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 6.400838] wlan0: authenticate with c8:d3:a3:35:13:f2
[ 6.410308] wlan0: send auth to c8:d3:a3:35:13:f2 (try 1/3)
[ 6.412242] wlan0: authenticated
[ 6.412932] wlan0: associate with c8:d3:a3:35:13:f2 (try 1/3)
[ 6.416988] wlan0: RX AssocResp from c8:d3:a3:35:13:f2 (capab=0xc11 status=0 aid=1)
[ 6.417065] wlan0: associated
[ 6.417083] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 15.825736] audit_printk_skb: 45 callbacks suppressed
[ 15.825745] type=1400 audit(1389771454.044:26): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=633 comm="cupsd" pid=633 comm="cupsd" capability=36 capname="block_suspend"
[ 48.038646] type=1400 audit(1389771486.305:27): apparmor="DENIED" operation="capable" parent=1 profile="/usr/sbin/cupsd" pid=633 comm="cupsd" pid=633 comm="cupsd" capability=36 capname="block_suspend"
[ 321.749219] wlan0: deauthenticating from c8:d3:a3:35:13:f2 by local choice (reason=3)
[ 321.763556] cfg80211: Calling CRDA for country: GB
[ 341.876977] wlan0: authenticate with c8:d3:a3:35:13:f2
[ 341.888807] wlan0: send auth to c8:d3:a3:35:13:f2 (try 1/3)
[ 341.890852] wlan0: authenticated
[ 341.895341] wlan0: associate with c8:d3:a3:35:13:f2 (try 1/3)
[ 341.903235] wlan0: RX AssocResp from c8:d3:a3:35:13:f2 (capab=0xc11 status=0 aid=1)
[ 341.903326] wlan0: associated
[ 390.279961] cfg80211: Calling CRDA to update world regulatory domain
[ 405.620904] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 415.405529] wlan0: authenticate with c8:d3:a3:35:13:f2
[ 415.416448] wlan0: send auth to c8:d3:a3:35:13:f2 (try 1/3)
[ 415.418504] wlan0: authenticated
[ 415.422195] wlan0: associate with c8:d3:a3:35:13:f2 (try 1/3)
[ 415.426308] wlan0: RX AssocResp from c8:d3:a3:35:13:f2 (capab=0xc11 status=0 aid=1)
[ 415.426382] wlan0: associated
[ 415.426445] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
dario@ProBook:~$
